QA

How To Apply Window Film Without Bubbles

How do you get bubbles out of window film?

Poke a tiny hole in each bubble with a straight pin. The hole needs to be tiny, and you need to use caution not to rip the film. Make sure the window is still warm and damp, then use a credit card or other straight edge to slowly smooth the bubbles. Smooth toward the edge that is closest to the bubble.

Can I use soapy water to apply window film?

Just mix water and a small amount of liquid soap in a clean spray bottle. Professionals recommend baby shampoo or dish soap without any kind of grease-cutting agent as this may interfere with film adhesion. Rear windows have compound curvatures that render the application of window tinting film more difficult.

How do you fix a bubble in your window tint?

If you have larger bubbles or bubbles that have formed in older tint, then they will not go away. You can get rid of bubbles that are causing problems by carefully pricking them with a pin or sewing needle and then smoothing a credit card over the bubble to make it disappear.

How long does it take for bubbles in window tint to go away?

The bubbles often come about as a normal part of the application process, as the water gets trapped between the window and the film. In most cases, these bubbles disappear within two weeks, depending on the amount of sunlight that your car is exposed to.

Does window film go on the inside or outside?

In most cases, window film is installed on the inside of the glass. This allows for maximum durability. On vehicles, the window tint is hand-cut on the outside of the glass, then installed on the interior of the glass.

Can I use Windex to apply Gila Window Film?

Can I use Windex to use Gila Window Film? It must be absolutely clean and free of dirt. Do not use Windex or other household cleaners on the glass as the film does not adhere well and the chemicals in the cleaners can degrade the plastic.

How do you make soapy water for window film?

o For wetting solution, use a solution of mild dish soap (i.e., Dawn® or Joy®) and water. For a 32oz. spray bottle, add 4 to 5 drops of soap.

Can you apply window film with water?

Cut and Apply the Film Cut the pieces of film so they measure about 1/2″ larger than the window panes being covered. The water makes it easier to position the film and helps hold it on the window.

What is window film application solution made of?

A: If Gila Application Solution is not available, you may use a mixture of water and no tears baby shampoo (without conditioner). Mix one quart of water and ¼ teaspoon of shampoo in a spray bottle. Other liquid soap products contain ingredients that may reduce the effectiveness of the film’s adhesive.

Why is my tint bubbling?

What Causes Window Tint Bubbles? Window tints are bubbly because of the water trapped between the window and the dye. Bubbles in the window tints are normal after a few hours of installation. Bubbling can also occur if your window tints are losing its adhesive properties.

How do you get bubbles out of Rear Window Tint?

Warm the tint on your vehicles windows by placing it in the sun or by using a hair dryer lightly over the bubbles. Spray a small amount of water onto the surface of the window tint. Apply only enough water to lightly dampen the surface. Use the tip of a small sewing needle to puncture a hole in each air bubble.

How do you make window tint stick?

Dry Adhesive You won’t notice anything sticky when you remove the protective film. The adhesive is water-activated (WAA) usually by spraying with a solution of soap and water and can be moved and repositioned on the window before squeegeeing into place.

Does window tint get darker as it dries?

It does not darken when turned on. After drying it will appear darker, but not noticeably darker. You have to look for at least 15% if you want to get darker.

Is it normal to have little bubbles after window tinting?

Soap/air bubbles look like whitish, soapy residue and occur when the film is installed without properly preparing and cleaning the windows. Water bubbles – Also known as blistering, water bubbles are normal occurrence after window tint application and should go away over a certain period as the film cures.

Can I roll my windows down 3 days after tint?

Almost all the tinting professionals recommend that the car owners must wait at least 3 – 4 days after the tinting is installed before rolling the windows down. By waiting for 3 – 4 days, you can ensure that the tint is adhering to the glass properly.

Can window film damage windows?

If window film is installed incorrectly, it can damage the seals around your double-paned windows. And, even more unfortunately for the homeowners, this damaged seals and fogged windows must be repaired or replaced at their expense because the manufacturer will no longer honor the warranty.

How does one way window film work?

To deliver one-way privacy, the most effective and popular course of action is the application of a reflective film. Once applied, the film will give the exterior side of the glass a mirrored effect during daylight hours, preventing vision through the glass, whilst maintaining the view from the inside out.

Does putting plastic on your windows really help?

Plastic window film covers can reduce drafts and make a home feel warmer during the winter. They are also a relatively inexpensive way to reduce condensation buildup and lower energy bills. Window wraps can also seal air leaks around the window, when these leaks extend over woodwork.