Table of Contents
Remove the battery from the scale. Set the scale on the floor (no carpet) without the battery in place. Stand on the scale for 10 seconds (still without the battery). Carefully replace the battery without pressing any buttons or activating the scale.
How do you calibrate a Taylor weight scale?
The following reset procedure is used when the scale shows an err2, err, 0.0, inaccurate weight, or some other unusual error. Remove the battery from the scale. Sit the scale on a hard surface floor. Step up onto the scale, stand still for about 5 seconds and step off the scale. Re-install your battery.
How do I know if my Taylor scale is correct?
Place one foot on the scale, using just enough weight for the display to show dashes or zeroes. When the display turns on, remove your foot. Once the scale turns off, step back onto it with both feet to see accurate weight.
How do I reset my Taylor Food scale?
Press the tare button and the scale will reset to zero. If you want to weigh more than one food in the same bowl, add the food, hit tare, and the readout goes to zero. You can then weigh the additional foods in the same bowl, just getting the weight of that additional food.
How do you reset a Taylor thermometer?
To reset the base, you need to remove the batteries and then reinsert. This will also clear out the base unit for time, calendar, etc., if your product has these features.
Are Taylor body fat scales accurate?
On average, the Tanita scale, Taylor scale and Weight Watchers scale each reported our testers’ body fat 4 percent more than the “gold standard.” Consumer Reports tested the same six scales in March and came to the conclusion that, “The results were unimpressive: None was very accurate.”Jun 24, 2016.
How do you calibrate a scale?
Calibrating Your Scale Power on the scale and allow it to warm up (usually 30 seconds) Begin the calibration mode sequence. Follow the instructions on the scale’s display. Once the calibration process has been completed, remove the calibration weight and return to normal weighing modes.
How do I fix scale error?
You need to reset your scale using the instructions below; Remove the batteries. Leave the scale for about 10 minutes after removing the batteries. Re-insert the batteries and confirm the polarity is good. Place your digital scale on a flat surface, and confirm the feet are clear of any dirt or rust particles.
How do you set Taylor scale to grams?
Place the scale on a hard, level surface. Press the “ON/OFF” button to turn the scale on. The display first shows. Your scale is set at the factory to weigh in ounces. To switch to grams, Place the item to be weighed on the center of the platform. The scale will turn off automatically after 1½ minutes of non-use.
Can you calibrate a digital scale?
Calibrating your digital scale is the best way to prolong the scale’s quality and overall lifetime. It only takes a few minutes, and when done correctly, guarantees the measurements you are taking are accurate each and every time.
How do you fix a scale that won’t calibrate?
Even if your scale is calibrated, it could show inconsistent readings if it’s resting on an uneven, tilted or rounded surface. Use a mouse pad or static-reducing pad on a flat, hard surface underneath your scale to steady the scale and ensure correct results every time.
How do I reset my digital scale?
Remove all batteries from the back of your scale. Leave the scale without its batteries for at least 10 minutes. Make sure that the battery compartment is clean, and the contact terminals are free of debris or residue. Check that the batteries have the correct polarity and reinsert them firmly in place.
How do I reset my kitchen scale?
1. Place the first item(s) within the center of the Weighing Area of the scale to take a measurement. 2. Without removing the item(s), press the ZERO/ON/OFF button to reset the display to 0.
What can I use for a 500 gram calibration weight?
If you want a household ‘something’ that weighs 500 grams, use 100 sheets from a packet of A4 paper. By using other quantities of paper, it’s possible to ‘bracket’ the accuracy of your scale: 50 sheets will weigh 250 grams; 200 sheets will weigh 1000 grams or 1 kilogram (1kg) and so on.
Can a Taylor thermometer be calibrated?
Fill a tall glass with ice and add cold water. Place and hold the thermometer in the ice water for 30 seconds without touching the sides or bottom of the glass. If the thermometer is a dial thermometer, allow 1-2 minutes for temperature calibration.
How do I adjust my Taylor digital thermometer?
To calibrate your thermometer, fill a glass with ice and then fill the glass with water. Give it a stir and place the thermometer into the ice water, ensuring that the dimple is underwater. Wait until the thermometer’s reading stops moving and turn the dial until it reaches 32 degrees Fahrenheit.
How do you adjust a Taylor digital thermometer?
Press and hold the “°F/°C” button for 3 seconds to switch between Fahrenheit and Celsius temperature displays. 5. Press the “UP” or “DOWN” button to set the desired target set temperature. The target “SET TEMP” appears on the right side of the screen.
