Table of Contents
To adjust the draw weight on a compound bow, take it to an archery shop. A bow technician will evenly tighten the limb bolts and check the draw weight. One full turn of the limb bolts usually changes its weight about two pounds. By increasing your draw weight just a few pounds at a time you’ll avoid injury.
How much does it cost to get a bow draw length adjusted?
The changing out of the modules usually requires a hexagonal wrench and can be done without pressing the compound bow. While certain companies will offer lifetime modules changes, most new modules have to be purchased. Average cost is $8 to $25.
Is 70 lb draw too much?
For example, a bow with a 70-pound peak weight and a 80% let-off should have a holding weight of around 14-pounds. Being able to hold a bow at full draw for 30 seconds is great, but if you’re shaking, struggling, and exhausted at the end of that time, then you’re not going to be able to make an ethical shot.
Does brace height change draw weight?
no. When you get to the end of your draw length it should be the same. But the preload is higher so the weight when you start to draw starts heavier as you alluded to.
What draw weight do most hunters use?
Some shooters are capable of shooting 70, 80 or 90lbs, but most adult males shoot between 60 and 70lbs. Today’s bows are extremely efficient and 40lb compound bows are more than capable of harvesting many big game animals. For whitetail deer hunting anything above 40 lbs is fine.
How do I know my draw weight for a compound bow?
Just stand naturally. Have someone else help you, and measure from the tip of one middle finger to the other. Then simply divide that number by 2.5. The quotient is your approximate draw length (in inches) for your body size.
How does riser length affect draw weight?
The longer the riser, the more draw weight you loose. The shorter the riser the more draw weight you gain. Most standard ILF limbs are rated on either a 17″ or 19″ riser, and most manufacturers will tell you in the limb info what riser length they are rated on.
Can you change the brace height on a compound bow?
To adjust brace height, unstring the bow, remove the bottom string loop, and then twist or untwist the string. If your brace height is too low, give the bowstring two twists to increase the brace height by about ¼ inch. If your brace height is too high, unwind a few twists from the bowstring.
Does brace height really matter?
It’s long been said that brace height is a key factor in a bow’s accuracy. Shorter brace height bows tend to have the reputation of being tough to tame. Instead of a bow with a 5″ brace height they would select a bow with a 6″ or 7″ brace height to maximize their accuracy.
How do I know if my bow is drawn too long?
The bow arm should move toward the target when the shot is fired. If the bow arm drops or swings to the side, the draw length is probably too long. When this happens, the scapula has already pushed the bow arm out as far as it can extend before the arrow is released.
How do I know if my bow draw length is too long?
The ideal draw length for you is the one that allows you to anchor in a comfortable position, with your bow arm elbow unlocked (slightly bent) and your release arm elbow and forearm pointing straight away from the target. If the release arm elbow points left or right, your draw length is too long or too short.
Does draw length change with a release?
Registered. Your draw length will not change by using a longer release aid. The only thing changing is your anchor point.
How do you adjust the poundage on a compound bow?
To adjust the draw weight, we have to unload or load more stress (flex) on the limbs; we do that by tightening or loosening the limb bolts. To raise draw weight to maximum poundage, tighten the limb bolts (clockwise) until both limbs are tight against the riser.
How do you adjust the draw length on a PSE compound bow?
To change draw length on the ECS: Loosen the two 8-32 size 15 Torx® screws holding the module to the cam approximately 1-1/2 turns, move the module to the desired setting. The setting will be in the window marked “DL” move the module to the same setting on both top and bottom cams.
What is John Dudley’s draw length?
Overall draw length of 29.125″ has my Stan Shootoff perfect and a tad too long with my TRU Ball HT.
What is the best let off on a compound bow?
A standard compound bow will have let off of between 60% to 90%. These are just a rule of thumb though, and it does vary between different models. Some bows even have a feature of a changeable let-off percentage.
Are compound bows easier to draw?
Compound bows are easier to draw, aim and shoot. Their cams or wheels roll over during the draw cycle to reduce the bow’s draw weight at full draw.
How hard is it to pull back a 40 pound bow?
The draw weight is basically, “How strong do I need to be in order to pull this thing back?” For a recurve bow, it’s measured by pulling back to 28 inches. So for a 40 lb bow, it means that it takes 40 lbs of force to pull back the string 28 inches for a recurve.
How far can a 20 lb bow shoot?
Even out to about 20 yards, with a broadhead, yup. If you were good, 30-40 yards most likely. Those arrows don’t slow down as much as you think. Recurve bows are a different beast (think Arrow), but compound bows are very fast and thus there’s a lot of energy behind that arrow.
How long should my arrows be for a 28 draw?
If you’re a 28-inch draw length and want an arrow that ends at the front of the riser, your arrow length would be around 27 inches. However, your arrow length can be longer if you need to weaken the spine of your arrow. For safety reasons, your arrows shouldn’t be cut too short.
What is the ideal draw weight for a bow?
Build, Bodyweight and Suggested Bow Draw Weights Type of Person/Build Weight (lbs) Compound Suggested Draw Weight (lbs) Average Woman 130-160 30-40 Large/Strong Woman 160+ 45-55 Small/Slight Man or Older Boy 120-150 45-55 Average Man 150-180 55-65.
