QA

Quick Answer: Can Ceramic Disc Be Reversed

Are ceramic tap cartridges handed?

Externally the most obvious feature of ceramic taps is that they are only quarter turn, instead of at least two and a half turns used with washer taps. The quarter turn is normally ‘handed’ when a pair are purchased – i.e. one tap turns clockwise to open, while the other tap turns anticlockwise.

Can you change the direction a tap turns on?

These compression-type valves and stems are threaded to turn either left or right, with hot normally being the right-hand thread. To change handle directions on a faucet of this type, either switch the hot and cold valves and stems, or purchase a new set threaded to turn in the desired direction.

Can ceramic disc taps be repaired?

Ceramic tap cartridge repair or replacement. Before conducting this process, please check with your local plumber (or get in touch with our expert team here) that you have acquired the correct replacement ceramic disc catridge. To repair or replace a ceramic disc cartridge you will need: New ceramic tap cartridge.

Why do new taps turn the wrong way?

It’s the manufacturers choice of tap heads that is wrong. They are quarter turn cartridges and should have lever type heads. ‘ However not everyone appeared to understand the issue – with many thinking Jeremy was confused by the fact that hot was on the left and cold on the right.

How do ceramic tap cartridges work?

Ceramic disc cartridges are simply two ceramic discs with holes through them. One disc is fixed in place whilst the other moves with the tap handle. When both discs are in alignment, the water is allowed to flow through the tap. When they are no longer aligned, the water stops.

Are tap valves reverse thread?

The thread on the hot tap will be normal ie anti-clockwise to undo.

Which way should a tap turn on?

So, when hot water was introduced, the logical conclusion about where to put this new tap was simply on the opposite side of the cold water tap – the left! So, the common sense answer is that the hot tap is on the left because people are mostly right handed and the cold tap is used the most often.

Do taps turn clockwise?

Just like with screws and bottle caps, the following applies: water taps are closed turning them clockwise and opened counterclockwise. To remember this, you can use the following mnemonics: Turn the tap in this same direction.

Why is my ceramic disc tap leaking?

Ceramic disc taps feature a cartridge within the tap that contain a pair of ceramic discs. If you do experience dripping this is usually caused by a scratched ceramic disc. In order to rectify the leak you must replace the entire cartridge as follows.

What causes a ceramic disk faucet to leak?

If the faucet leaks, the culprits are usually the inlet and outlet seals. When repairing a disc faucet, the handle should be on in the on position.

Can tap cartridges be repaired?

How to repair a ceramic tap, with advice on tap valve fitting, ceramic tap washer repair and ceramic tap cartridge replacement. It is very rare for the ceramic discs to wear out and the need to replace them is even rarer. It is, most often, just a case of dismantling the moving parts and servicing them.

What are quarter turn taps?

Traditional taps with a washer are at least two and a half turns to turn on to full pressure. Quarter turn taps use ceramic discs and is only a 90 degree turn to be on full pressure.

Are hot and cold tap valves the same?

In other words both the Hot and Cold valves are the same but open in mirror directions so please select the valve you require according to how your taps work. If you have a two lever ‘filterflow’ or ‘aquifier’ tap then the hot side has a valve and the cold side has a diverter cartridge for the cold and filtered cold.

How do you dismantle a tap?

To remove the tap head, simply prise off the tap indicator cover and remove the retaining screw beneath it. Once the screw is removed the tap head should then pull off. Occasionally, once the retaining screw has been removed the head of the tap will still not come off.

Are ceramic disc taps any good?

Plumbing connections for ceramic disc are no different to other taps, and with that comes all the ease of a quarter-turn technology, and a more durable, longer lasting tap without those annoying leaks. From a long-term maintenance point of view, ceramic disc taps are much better than normal taps.

How does a water tap cartridge work?

HOW DO CERAMIC TAP CARTRIDGES WORK? A ceramic tap cartridge consists of a valve body holding two discs, each with holes through the middle. In the closed position the holes on the two discs are in different positions and this prevents water flowing through the tap.

How long do ceramic tap washers last?

Ceramic tap washers can last years, but other types can last for as little as twelve months depending on how frequently they’re used.

Why does my tap drip after I turn it off?

The faucet valve (working parts) is housed in the handle and controls the on/off, volume, and temperature control. Over time, a faucet valve can lose its ability to make a water-tight seal, so water will drip out even in the off position.

Which way do you unscrew a tap valve?

You screw a valve out ‘anti-clockwise’ – which means on a standard 2 lever tap where you pull both levers towards you to turn on, and push back up to turn off (and hot on the left and cold on the right – on the hot side you have to push away from you i.e. towards the wall behind the tap, and for the cold side to loosen Jan 16, 2013.