Table of Contents
The ShowDown comes with a single cam and idler wheel system. In addition this cam allows 1″ draw length adjustments from 25-31″ and 1/2″ post adjustments. This set up also has 80% let off and has a 290 fps IBO speed.
Can draw length be adjusted?
Adjustable cams allow the archer to adjust his or her draw length with the use of an hexagonal wrench without, in most cases, pressing the compound bow. Adjustable compound bow cams allow archers to adjust anywhere from 3 inches up to 13 inches depending on the compound bow.
How do you adjust the draw length on a bear Legion?
The Bear Archery Legion Eccentric System (cams) Draw length can be adjusted from 26″ to 31″ in 0.5″ increments, directly through the power cam on the bottom limb.
How do you change the draw length on a bear in divergent?
Draw length changes are made by simply moving the draw stop to the desired position, then rotating the modules accordingly. See draw length settings below. To change draw length, draw stops must be adjusted before the module.
How do I know if my bow draw is too long?
The bow arm should move toward the target when the shot is fired. If the bow arm drops or swings to the side, the draw length is probably too long. When this happens, the scapula has already pushed the bow arm out as far as it can extend before the arrow is released.
How do I know if my bow draw length is too long?
The ideal draw length for you is the one that allows you to anchor in a comfortable position, with your bow arm elbow unlocked (slightly bent) and your release arm elbow and forearm pointing straight away from the target. If the release arm elbow points left or right, your draw length is too long or too short.
Can you shorten draw length by twisting string?
You can also twist or untwist your strings and cables. Twisting the cables an even amount on each side will lengthen your draw length, untwisting them will shorten your draw length. You can twist or untwist the string to adjust draw length, but it won’t quite do as much.
Does changing draw length affect sights?
Shortening the draw length will cause the peep to be higher, which will cause you to tilt your Bow upward to align peep with sight housing. This will make you hit higher. The Bow will be a little slower but you still may have to move the peep down or sight up.
Is 70 lb draw too much?
For example, a bow with a 70-pound peak weight and a 80% let-off should have a holding weight of around 14-pounds. Being able to hold a bow at full draw for 30 seconds is great, but if you’re shaking, struggling, and exhausted at the end of that time, then you’re not going to be able to make an ethical shot.
How long should my arrows be for a 28 draw?
If you’re a 28-inch draw length and want an arrow that ends at the front of the riser, your arrow length would be around 27 inches. However, your arrow length can be longer if you need to weaken the spine of your arrow. For safety reasons, your arrows shouldn’t be cut too short.
How long should my arrows be for a 27 inch draw?
The arrow must be 29″ in length and supported by two points, which are 28″ apart. The number of inches the arrow deflects or bends due to the weight, is the spine size or measurement of an arrow. DYNAMIC spine describes the way an arrow reacts from the stored energy of a bow as it is shot.
How do you change the draw length on a bear Royale?
right alongside your young hunter. The draw weight can be easily adjusted from 12” to 27”. All draw length and draw weight adjustments can be made using an Allen wrench, removing the need for a bow press.
How do you change the draw length on a Bear Whitetail compound bow?
Find the label that tells you the draw weight range and decide whether the draw weight needs to be increased or decreased. Use a 7/32-inch hex wrench to turn the top limb bolt one turn. Clockwise increases the draw weight, and counterclockwise decreases the draw weight. Turn the bottom limb bolt one turn.
Is longer draw length better?
Since the time always stays the same, we can conclude that the higher the distance (draw length), the greater the speed needed that means longer draw length leads to greater arrow speed and faster arrow.
Does draw length matter?
WHY IT ALL MATTERS Having the right draw length and draw weight for your hunting profile is not just important for performance, but important for safety as well. Also, a longer draw length can force your front arm to a full extension, leaving your inner elbow in direct path of the string and potential injury.
How long should my draw length be?
Resist the temptation to make your draw length longer than it should be, as this will effect your accuracy. Your wingspan typically is the same as your height in inches; So your height in inches minus 15 and then divided by 2 will be your draw length, or at least a very good starting point.
Does draw length affect FPS?
For every inch you reduce your draw length, you will lose roughly 10 fps of arrow speed. On similar bows rated over 335 fps, the loss is closer to 10 to 12 fps.” 3. For every five grains of arrow weight added, you will lose 1-1.5 fps in arrow speed.
How does draw length affect draw weight?
Yes, changing to a longer draw length on a bow increases the draw weight. Reduce the draw weight with the oimb bolts if you can. I have done this in the past by using a longer bow string. FOr each inch longer, it added 3 or 4 pounds of weight if I rememebr right.
What is the average draw length on a bow?
If you have an average draw length of 27 to 29 inches, any modern compound bow matched with a good arrow and set to 60 pounds will work just fine on whitetails, mule deer, pronghorns, and the like with whatever broadhead style you prefer, so long as your shot placement is good.
Can you shorten bow string?
To increase the string height (distance from the bow to the string), you need to shorten the string. Hold the string between thumb and forefinger, just above the bottom loop. Spin the string between the thumb and finger so that you add twists to it. The more you twist the string, the shorter it gets.
How much can you shorten a bow string?
Shortening the bow string w/ovrhand Knot One over hand knot shortens the string about an 1/8th of an inch. I make the knot about an inch down from the base of the serving of the string loop. Anyone else do this and has anyone also tried this on compound bow strings?Aug 8, 2007.
Is the elite Valor a good bow?
The Elite Valor is an excellent option for bowhunters looking to step into a high quality, great drawing, smooth shooting machine. Elite’s proven platform of form, fit, and finish – combined with the original shootability make the Valor a strong contender among all bows.
