Table of Contents
Fortunately, it is possible to place stamped concrete over existing concrete. Stamped concrete overlays are durable options for upgrading, repairing, and enhancing existing concrete.
Can you stamp concrete after it dries?
You can only stamp concrete when it is still wet from a pour. To add texture to an existing patio, pour a fresh layer of concrete over the old and stamp it, provided the existing patio is in good condition.
How do you attach concrete to old concrete?
Drill 5/8-inch diameter holes six inches deep into the old concrete. Flush the holes with water. Inject epoxy into the backs of the holes. Insert 12-inch lengths of rebar into the holes, twisting them to ensure an even coating of epoxy around their circumferences and along their lengths within the holes.
How long after concrete is poured Can you stamp it?
“But, in general, when you can touch the concrete and not have any sand on your hand, it’s about time, when that laitance is crusted enough, to put a release agent on there. Generally, it’s within an hour or two.” Frazier recommends getting enough stamps to cover at least the width of the slab.
Can you put a thin layer of concrete over existing concrete?
How Thin Can You Pour Concrete Over Existing Concrete? The thinnest that is usually used when pouring concrete, in general, is about 2 to 2 ½ inches. That also applies to this pouring new concrete over old concrete. Any thinner than 2 inches would be too thin.
Do concrete overlays last?
How long is the life span of a decorative concrete Overlay? If maintained and sealed properly, the DCO can last 20 years and be a permanent topping to the concrete slab. Every 5 to 7 years it should be resealed.
Can I pour concrete over dirt?
Long story short, yes you can pour concrete over dirt.
Does concrete stick to old concrete?
What Will Concrete Not Stick To? Concrete does not adhere to: Concrete – Dried concrete doesn’t have any natural bonding agents, so in order to get wet concrete to bond to existing concrete, a bonding agent will need to be used.
Can I pour a 2 inch concrete slab?
If done properly, new concrete can often be poured right over an existing slab. For this to be feasible, the contractor needs to pour at least 2 inches thick, use smaller aggregate, and incorporate reinforcement such as welded wire mesh or fiber mixed into the concrete.
At what point do you stamp concrete?
If you leave a clean imprint about 3/16 to 1/4 inch deep, you can generally begin stamping. Another test is to place a stamp on the concrete and step on it. The stamp should hold your weight and not slide around or sink too deeply into the surface.
How hard is it to stamp concrete?
Stamping. The most unforgiving part is the actual stamping itself. A good stamped concrete job looks good, while a fair-to-poor stamp job looks horrible. Dealing with poor placement or poor finishing is one thing, but if the imprinting process isn’t done properly, it’s extremely difficult and expensive to repair.
What happens if you don’t seal stamped concrete?
An unsealed, decorative stained concrete surface will show faded colors in a matter of a few months. You could advise your customer that’s what happens with an unsealed project and let them make the decision about sealing, but rest assured that an “I told you so,” from you when the fading happens will not comfort them.
How do you stamp over existing concrete?
The best way to get stamped concrete over existing concrete is a stampable overlay. Stampable overlays are a thick overlay capable of accepting texture from stamps. These overlays are much thicker than microtoppings but not as much as a self-leveling overlay.
Will concrete overlay crack?
Unfortunately, most concrete has a tendency to crack, usually as a result of improper design or poor construction practices. As an overlay installer, you have no control over these factors. You are responsible for repairing any cracks in the existing concrete before resurfacing.
Whats the difference between cement and concrete?
What is the difference between cement and concrete? Although the terms cement and concrete often are used interchangeably, cement is actually an ingredient of concrete. Concrete is a mixture of aggregates and paste. The aggregates are sand and gravel or crushed stone; the paste is water and portland cement.
Are concrete overlays good?
Concrete contractors have a similar option with overlays and an unsightly slab: The overlaid section not only looks better but the chemistry behind today’s overlay offerings often creates a much more durable surface than what was already there.
Is concrete overlay any good?
Durability and Long Life-Span Concrete overlays are installed with a penetrating sealer that makes them more resistant to staining and scuffing. All you really have to do to keep these floors looking great is to maintain that sealer and to sweep and mop them regularly to keep dirt off them.
Can concrete overlay be removed?
Once you have a place started where the overlay is broken through, continue to remove the concrete overlay. This is easily done by prying up the concrete from underneath and breaking it into smaller pieces. Use a flat scraper with a long handle to drive under the overlay and lift up.
Do I need gravel under concrete?
Whether you pour concrete for a walkway or patio, a strong gravel base is required to prevent the concrete from cracking and shifting. Gravel is especially important in clay soil because it doesn’t drain well, which results in water pooling under the concrete slab and slowly eroding the soil as it finally drains.
Can I use pea gravel under concrete?
If the soil is disturbed and packed or unstable such as some clays, a base will provide a solid underpinning for the slab. If you use crushed rock and dust, it will need to be packed. It will pack substantially. Pea gravel, on the other hand won’t pack.
Do you need to put plastic under concrete?
Water vapor will always move from a high relative humidity environment below the building into an area of low relative humidity – even through concrete. That’s why nearly every expert in the concrete industry recommends a below-slab vapor barrier to stop the vapor drive of water upward and into your building envelope.
What is poor man’s concrete?
Soil-cement is a mixture of Portland cement, natural soil, and water used to form a hard, semi-rigid paving surface. It is most often used in highways or as a sub-base for asphalt or other forms of paving, but it can also be used as a cheap stand-alone paving surface for driveways, sidewalks, patios, or garage floors.
What do you use to bond concrete to concrete?
QUIKRETE® Concrete Bonding Adhesive (No. 9902) permanently bonds new concrete, plaster, and stucco to existing concrete, plaster, and stucco. Eliminates the need for roughing the surface before the application.
Can I pour concrete 1 inch thick?
There aren’t many reasons to have only a 1-inch thick concrete surface. It is too thin to use as a flooring just by itself; however if you need to resurface damaged concrete, a 1-inch layer is a good amount. The old surface is prepared so that the new concrete will adhere, then the new cement is added.
