Table of Contents
Normal skate bearings need speed washers (or “speed rings”) to stop the bearing from fouling on the axle nut or the hanger face. If you have normal skate bearings (ie not “Built In” bearings – below), then you really should have some speed rings. If you have BuiltIn bearings, then you don’t need them.
Are speed rings necessary?
Speed Rings are an often overlooked part of your skateboard, but not having them could be greatly jeopardizing your performance! Speed rings go on the outside of your bearings to give more clearance, allowing an uninhibited continuous roll.
Do Built in bearings need speed rings?
The solution: Longboard bearings with built-in spacers Longboard bearings with built-in spacers have their inner ring (race) elongated on both sides, acting as the bearing spacer and speed washers. No extra bearing spacers and speed washers are required.
Are ceramic bearings worth it skate?
Ceramic bearings for skates and skateboards are popular because they are stronger, reduce friction, and last much longer than the typical metal ball bearing. Many companies produce ceramic bearings today and many serious skaters prefer them for the best ride.
What are speed rings for?
Speed rings are thin metal washers that sit on your axle on either side of your wheel. They are there to reduce friction between the outsides of your bearings and your axle nut on one side, and the edge of your hanger on the other side.
Are speed washers important?
Washers are used to prevent bearings from rubbing up against the truck hangar& axle nut. Washers increase the life of bearings & provide a much smoother ride.
Do you need spacers between bearings?
Bearing spacers are totally optional; longboarders and casual skaters likely won’t put enough pressure on their boards to ever need them, though they are definitely a good investment if you want to slide, do a lot of tricks, and generally skate hard. Unlike bearings, bearing spacers are not one-size-fits-all.
Do speed washers come with bearings?
Build it up and go skate! Trucks come with a hanger, baseplate, kingpin, bushings, speed washers and axle nuts (nylon locknuts). Each truck gets a total of 4 bearings (2 on each axle). In this step, slide one speed washer onto each axle.
How do you clean ceramic bearings?
Full ceramic bearings are maintenance free. However, they can be washed using regular tap water or a standard bearing cleaner product if required. Make sure the bearing is completely dry before replacing it. These bearings do not need lubricant to operate, so there is no need to add an oil or grease at this stage.
Is speed cream good for bearings?
We have found this lubricant to be superior to Teflon™ based lubricants in skate environments. Speed Cream R.F. makes your bearings faster and is very long lasting.
Do you need to lube ceramic bearings?
No, full ceramic bearings can be run completely dry. They do not need lubrication to run. Ceramic is non-porous, unlike steel, as a result it is virtually frictionless. Because there is no heat buildup and virtually no friction, full ceramic bearings can be run completely dry.
Do ceramic bearings make a difference skateboard?
“Hybrid” Bearings with Ceramic balls and steel races have a problem – Ceramic is around 30% harder than steel, so if you subject the bearing to a really big impact, the balls can actually permanently deform the steel races, leading to slower roll speeds and much faster bearing wear.
Do ceramic bearings make a difference?
According to research, a well-made ceramic bearing will roll faster, saving you energy and allowing faster cruising speeds compared to an equivalent steel bearing. This is because the properties of ceramic allow the creation of rounder, smoother bearings.
What bearings does nyjah use?
Nyjah Huston – Bones Bearings Team – Bones Bearings.
Do you need speed rings and spacers?
Also, we strongly recommend bearing spacers and speed rings. These make sure the bearings are properly aligned and seated perfectly.
Where do speed washers go on a skateboard?
To set yourself up, set the skate on its side again. Most trucks come with two axle washers per wheel, for a total of eight. These washers should go on either side of wheel to help it spin smoothly. To attach each wheel, slide on the first washer followed by the wheel with bearings followed by the second washer.
Do you need washers for bushings?
For a barrel and stepped bushing combo we’d suggest that you use flat washers beneath the boardside stepped bushings, and cupped or flat washers on the outer end of your roadside barrel bushings. Cupped washers will not work with stepped bushings.
What are speed washers skateboard?
Speed washers are slipped over the axle between the nut and the bearing, and the hanger and the bearing. They serve as a buffer between the nut and the bearing, which allows your wheels to rotate quickly while also protecting the bearing face from damage.
How important are bearing spacers?
Why Bearing Spacers are Important Bearing spacers sit within the wheel on the axle between the two bearings. This makes sure the inner races of the bearing are properly lined up. When these are aligned correctly, the balls and outer races also align.
Are spacers necessary?
Spacers push your jaw forward by adding space at the back of your mouth. They also make room for your braces if the back of your mouth is too tight to fit them properly. Not everyone needs spacers. They’re typically only used for a week or two at a time.
Do I need spacers for skateboard bearings Reddit?
Most importantly, they remove all ‘play’ or rattling in your wheels. Spacers prolong the life of your bearings by managing side-loading. They enable a wheel to slide smoothly and drastically reduces chatter. They keep your bearings parallel while spinning.
What are bearing washers skateboard?
Speed washers increase speed and promote longer bearing life by reducing friction between the bearing and axle nut and hangar. These washers are the standard size and will fit on all skateboard/longboard trucks that have 8mm axles (virtually every truck has the standard 8mm axle size).
Do all bushings fit all trucks?
Bushing tightness depends on each rider’s preferences, and bushings can be easily adjusted to suit your needs. Skateboard truck bushings are all the same size, and will fit any skateboard, longboard, or cruiser sold on Warehouse Skateboards. Check out the available skateboard truck bushings currently in stock.
What can I use to clean bearings?
Acetone, isopropyl alcohol and mineral spirits are all good options. When using solvents, wear gloves and avoid contact with your skin. Use a dish or wide-mouthed bottle as a container to soak the bearings for several minutes, occasionally swirling the bearings around in the cleaner.
