Table of Contents
The blend door actuator(s) are typically located on the climate control case behind the dashboard.
Where is the blend door actuator located?
The blend door actuator(s) are typically located on the climate control case behind the dashboard.
Where are actuators located?
The AC actuator is located above or below the coil. It can be set to either single speed or variable speed. When it is not working properly, your AC will be ineffective, and your power bills can skyrocket.
How do I know if my blend door actuator is bad?
If you hear a droning or squeaking sound coming from the center of your dashboard, there is most likely something wrong with your blend door actuator. These sounds will usually get louder when you turn on your AC or change the temperature.
How long does it take to replace a blend door actuator?
Replacing the blend door actuator is actually a fairly simple process, and it should take no more than an hour. So the labor will cost you around $75 – $150 depending on labor rates at your local repair shop. In general, you can expect the total cost to be no more than $400.
Does the blend door actuator have a fuse?
The blend door actuator fuse in Your 2010 Ford F-150 can be found in the fuse panel that is located in the passenger’s footwell. The panel can be found behind a plastic door that has fuse written on it. The blend door actuator controls the blend door’s position.
What controls the blend door?
The blend door is controlled by the vehicle’s heater controls. If the actuator is an electric motor, the driver operates a knob to change from cold to hot. The knob tells the heater control “head” the preferred temperature setting and the control head commands blend door motor operation.
Why does my blend door actuator keep going out?
What Causes a bad blend door actuator? A blend door actuator is linked to an air control door pivot found on the last drive of the unit; a plastic gear set is frequently rotated from one side to another by the electric motor.An actuator can become faulty if the plastic gear set turns out to be fragile and it breaks.
What is door actuator?
A door lock actuator is basically a reversible motor (or a solenoid on some vehicles) with gears that operate the door lock. The motor reverses direction so that when you press the switch to unlock the doors, the lock moves in one direction. The module then supplies the power to the actuator to unlock the door.
Why is my car blowing hot air on one side and cold air on the other?
Blend door actuators are the most common reason for the car air conditioning to blow cold air on one side and hot air on the other. They can be diagnosed with an advanced scan tool. If it does not move with the adjustments and commands, there is a problem with the blend door actuator and it will need to be replaced.
Why is my AC cold on one side?
Due to the design of dual AC systems, low refrigerant is the leading cause of drastic temperature difference from one side of the dash to the other. In most cases after the proper charge of Freon is in the car, the temp will blow equally as cold like it should on BOTH sides!Dec 27, 2019.
Where is the actuator in a car?
The AC actuator is located underneath the dashboard attached to air distribution doors in the hvac box. Doors can control warm air/cold air blending, recirculated/fresh air control, or dual zone splitting. The motors can move the doors into many different positions, or just two.
Can I drive without a blend door actuator?
Safety: Can I drive without doing an HVAC Blend Door Actuator Replacement. Driving isn’t a problem for this environmental issue, but your passengers won’t be comfortable or happy. Don’t let them suffer, count on a mobile mechanic from Wrench.
How many blend door actuators does a car have?
Most vehicles have two blend door actuators, one on the driver side and one on the passenger side. Fortunately, you do not need to remove the dashboard in order to get to them. Some experts recommend that you disconnect the vehicle’s battery to remove and replace the blend door actuators.
How many actuators does a car have?
Typically, vehicles have 3 or 4 actuators. Vehicles with rear controlled HVAC will often have additional actuators to control the auxiliary unit, bringing the total per vehicle to as many as 6.
How do I reset my blend door actuator Ford?
First thing You will need to do is remove the fuse for the actuator from the fuse panel in the driver’s footwell. After that You will want to start the car and run the AC system for a few minutes. Finally shut off the car and put the fuse back in and see if the blend door works.
Where is fuse for blend door actuator on 2011 f150?
To locate the actuator’s fuse, visit the interior or cabin fuse box. It should be found on the right hand side of the truck in the passenger’s footwell.
