Table of Contents
When the supply is connected to the stator of a three-phase induction motor, a rotating magnetic field is produced, and the rotor begins rotating and the induction motor starts. At the time of starting, the motor slip is unity, and the starting current is very large.
What is starting current of induction motor?
The starting current of the induction motor is about 5 or 6 times the motor full load current. An induction motor of rating 11 KW,22 Amps,440 volts takes a high starting current of about 132 Amps. The current reduces as the motor accelerates towards its base speed or synchronous speed.
Are induction motors self starting?
The induction motor always runs at speed less than its synchronous speed. The rotating magnetic field produced in the stator will create flux in the rotor, hence causing the rotor to rotate. Single phase induction motors arenot a self-starting motor, and three phase induction motor are a self-starting motor.
What are the types of induction motor?
Types of Induction Motor: A Concise and Useful Guild
- Types of Single-Phase Induction Motors. Split Phase Induction Motors. 2&3. Capacitor Start and Capacitor Start Capacitor Run Induction Motors. Shaded Pole Induction Motors.
- Types of Three-Phase Induction Motors. Squirrel Cage Induction Motor. Slip-ring or Wound Rotor Induction Motor.
What is back emf in dc motor?
The back emf opposes the supply voltage. The supply voltage induces the current in the coil which rotates the armature. The electrical work required by the motor for causing the current against the back emf is converted into mechanical energy. And that energy is induced in the armature of the motor.
Does a single phase motor need a starter?
Single phase motors generally need a starter circuit to get them turning. That starter circuit is turned off by a centrifugal switch once the motor reaches a minimum RPM. Three phase motors do not require a starter circuit.
How inrush current is reduced in motor?
One is to use a soft starter — a device that gradually increases supply voltage to the motor terminals during startup, thus lowering inrush current and controlling startup torque. Similarly, a variable frequency drive reduces inrush current by controlling the voltage supplied to the motor.
What is the difference between inrush current and starting current?
The inrush current is the current transient that flows in the first cycle or so that establishes the magnetic field in the iron. The inrush current can be significantly higher than the locked rotor current with 2 – 2.5 times the start current being quoted by some.
How does a single phase induction motor start?
Starting Principle A single phase induction motor consists of a single phase winding on the stator and a cage winding on the rotor. When a 1 phase supply is connected to the stator winding, a pulsating magnetic field is produced. In the pulsating field, the rotor does not rotate due to inertia.
What are the types of single phase induction motors?
Types of single phase induction motors
- Split-phase motor.
- Capacitor-start motor.
- Capacitor-start capacitor-run motor.
- Permanent-split capacitor (PSC) motor.
- Shaded-pole motor.
Why induction motors are not self starting?
From the above topic, we can easily conclude that the single-phase induction motors are not self-starting because the produced stator flux is alternating in nature and at the starting, the two components of this flux cancel each other and hence there is no net torque.
How can we reduce the starting current of an induction motor?
Some of the techniques used to reduce the starting current of a squirrel induction motor:
- Soft starting (voltage control)
- Variable Frequency Drives (Voltage and frequency control)
- Star/Delta Starting.
- Stator impedance and/or resistance starting.
- Autotransformer Starting.
Why does an induction motor need a starter?
A starter is needed for a three phase induction motor because at the time of starting, if induction motor is started directly, it will draw a huge amount of current which can cause damage to adjoining equipments. which depends on slip i.e. R2(1-S)/S will be equal to “0”, i.e. rotor will act as short circuit.
Why are motors not self starting?
Above a certain size, synchronous motors are not self-starting motors. This property is due to the inertia of the rotor; it cannot instantly follow the rotation of the magnetic field of the stator. Once the rotor nears the synchronous speed, the field winding is excited, and the motor pulls into synchronization.
Why starting current is high in motor?
Why High Starting Currents: Resistance and leakage reactance circuit consist of resistance and leakage reactance of stator and rotor of induction motor connected in series. A load resistance (variable) is connected in series to the fixed rotor and stator impedance. During starting of the motor, slip will be one.
Do I need a motor starter?
Essential and Need of Starter with Motor Motors below 1 HP (0.7457) is directly connected to the power supply without starter because their armature resistance is very high and they have the ability to afford and pass higher current due to high resistance. The motor will not start to run at this stage.
Why is DC motor current so high?
Answer: The starting current is high as there is no back EMF or counter EMF present in the armature circuit because atstarting counter EMF is zero. It’s armature has very less resistance due to this it need more current at starting time. Hence DC starters are used to limit the starting current ofmotor.
Why Interpoles are used in DC machine?
Inter poles in dc machines help to reduce armature reaction effects in the inter polar regions and their windings are connected in series with the armature so that its effect can vary with the armature current.
What is the principle of induction motor?
The motor which works on the principle of electromagnetic induction is known as the induction motor. Electromagnetic induction is the phenomenon in which the electromotive force induces across the electrical conductor when it is placed in a rotating magnetic field.
Where is induction motor used?
Single-phase induction motors are used extensively for smaller loads, such as household appliances like fans. Although traditionally used in fixed-speed service, induction motors are increasingly being used with variable-frequency drives (VFD) in variable-speed service.
Can a motor run without a capacitor?
Without the capacitor the motor will not start automatically but without a capacitor, a flick on the shaft will make the single phase motor run in either direction, provided that the main winding is operation as it should do.
What are the causes of overheating of a DC motor?
The most common causes of overheating include:
- An unsuitable motor: Motors come in a range of sizes.
- The wrong voltage supply: Too many volts or too few volts can be damaging to a motor.
- A poor surrounding environment: A motor needs room to breathe so it can perform at its best.
