Table of Contents
Wood frame walls covered with dry wall are considered combustible. If no wall protection is used, the common radiant-type stove or heater must be spaced out at least 36 inches from the wall.
What is the minimum clearance for a wood stove?
All stoves require a minimum 36-inch clearance to unprotected combustibles above and on all sides of the stove. A single wall stovepipe must have a clearance to combustible walls and ceilings, measured at right angles to the pipe of at least 18 inches. No clearance is needed to noncombustible walls (i.e., concrete).
How do you protect a wall behind a wood stove?
Heat shields are a type of heat-resistant board placed behind a wood-burning stove or other heating appliance. They are necessary for protecting your walls and floors from damage and decreasing the risk of fire.
How close can a stove be to the wall?
There should be two inches of space between the back wall and a drop-in or slide-in (gas or electric) style range. A freestanding range (gas or electric) requires no space between it and the back wall. There should be at least twelve inches between any style range and the closest sidewall.
How close can a wood stove be to a wall with heat shield?
Using a “Heat Shield” on a single wall stovepipe allows you to reduce the clearances from 18″ to 6″ to the wall and 9″ to the ceiling. Many think stovepipe can run from the wood-stove, right up through the ceiling and roof.
How close can a wood stove be to cement board?
A combustible floor must be protected by a non-combustible material (like tile, concrete board, or certified to UL-1618 or as defined by local codes) extending beneath the heater and a minimum of 6″ from each side and minimum 16″ from the front face of the stove and minimum 6″ (or the rear clearance to combustibles Oct 1, 2011.
What do you put under and behind a wood stove?
Stone or brick is a common material to use behind a wood burning stove.
What can I put on the wall behind my stove?
Granite, stone and other natural or composite materials are also commonly used in backsplashes, whether in tile form or as larger pieces. These higher-end materials will mean an increase in budget, but also a stunning and long-lasting stove backsplash. Stainless steel is another popular option for stove backsplashes.
Where should a wood burning stove be placed?
The ideal location for a wood stove is close to the center of the area to be heated. This gives the best heat distribution. Avoid locating it near an exterior wall as this increases the heat loss to the outside, and decreases the heat gained from the stove.
How much space do you need on each side of a stove?
A minimum of 12 inches of landing space on one side of the stove, and another 15 inches on the other side, are the required landing area widths. As this is hardly enough room to set a single pot or pan, this should be considered an absolute bare minimum, with greater widths highly recommended.
Can you put a stove in a corner?
Can You Put A Stove In A Corner? Yes. A standard-sized stove and oven can be installed in the corner of the kitchen, provided that proper safety precautions are considered and maintained.
Does a wood stove pipe have to go straight up?
The pipe should be as straight and short as possible, with sections properly secured. If it must have angles, limit them to one or, at the most, two sweeping 90-degree elbows or the equivalent. The horizontal portion of the pipe should rise not less than one-quarter inch to the linear foot, to insure a good draft.
Can cement board be used behind a wood stove?
Safe wood stove installations require a heat shield that will prevent heat from the wood stove from creating a fire hazard in the building materials that form the exterior wall. Hardi cement board is an inexpensive solution that will form the foundation of an effective heat shield for any application.
Can you tile behind a wood burning stove?
ANSWER – Ceramic tile behind a woodstove works very well as long as it’s installed correctly over the right type of substrate. It’s important, though, that the tile is attached to a surface that’s not affected by heat. It’s best to use a concrete substrate like a mortar bed or a cementitious backer unit.
How close can a wood stove be to a non combustible wall?
The standard clearance recommended by the National Fire Protection Agency is 36 inches. This means that the back of the stove should be 36 inches away from any combustible material, such as woodwork, unprotected walls, furniture and even firewood.
What do you put on the floor under a wood stove?
How to Make Pads for Wood Stoves Backer Board Foundation. Concrete backer board, which is a tile underlayment, provides a heat-resistant, rigid foundation. Cinderblock Fireproof Mats. You can use cinderblocks to create fireproof mats for wood stoves. Use Heat-Resistant Firebrick. Stone or Tile.
Can you use sheet metal behind a wood stove?
Installing sheet metal behind a wood stove creates a barrier to protect the wall and reduce fire risks. Installing sheet metal with the correct clearances behind a wood stove can prevent radiant heat from igniting combustible materials in the wall, which could result in a house fire.
Can you put peel and stick tiles behind a stove?
Q. Can I use peel-and-stick backsplash panels behind the stove? Most—but not all—peel-and-stick backsplashes are heat resistant and pose no problem if installed behind a stove.
How far should tile be from stove?
When tiling a kitchen backsplash behind a stove, the best practice is to continue the tiles down the wall a minimum of one full course below the countertop height. This is done in order to prevent any visual discontinuity so you cannot see any untiled wall surface.
Do you need backsplash for slide in range?
Do I need a backsplash behind a slide-in range? Backsplashes are not mandatory, but they are everywhere in today’s modern homes. The controls on a slide-in range are in the front, not on a lip in the back of the range. So, if you install a backsplash, make sure it extends all the way to the base of the countertop.
Can I put a wood stove next to a window?
A wood stove needs to have at least 36 inches of clearance between an unprotected ceiling and the top of the stove. When installing a wood stove in front of a window, make sure the clearance is at least 36 inches from the glass to keep it from heating up and cracking or getting damaged.
