Table of Contents
What lengths do 4×4 come in?
Dimensional Lumber Nominal Size Actual Size 2×12 1-1/2″ × 11-1/4″ 4×4 3-1/2″ × 3-1/2″ 4×6 3-1/2″ × 5-1/2″ 6×6 5-1/2″ × 5-1/2″.
How much does a 10 foot 4×4 weigh?
x 4 in. x 10 ft. timber can weigh approximately 31 pounds when it is completely dry (no moisture content) and weigh between 41 and 48.5 pounds when the timber is new pressure treated for above or below ground.
How many fence posts come in a bundle?
5-6″x8′ CCA pressure treated fence post, 45/Bundle.
How much does a 12 ft 4×4 weigh?
Table of Pressure-Treated Lumber Weights Weight of Pressure-Treated Lumber 4 x 12 3.5 x 11.25 11.22 4 x 14 3.5 x 13.25 13.21 4 x 16 3.5 inch x 15.25 inch 15.2 lbs 6 x 6 5.5 x 5.5 8.61.
Is a 4×4 post really 4×4?
What are the dimensions of a standard 4×4 or 6×6 wood post? The lumber industry defines standard wood post sizes as 4×4 or 6×6. The outside dimensions of the standard 4×4 measure 3-1/2″ x 3-1/2″, and the outside dimensions of the standard 6×6 measure 5-1/2″ x 5-1/2″.
How long will a treated 4×4 post last in the ground?
A treated 4×4 will last 20 to 25 years in the ground if the conditions in the soil and climate are favorable. That number could increase to 40 to 75 years if you install the treated 4×4 in a cement ring rather than the soil. There are a few factors that influence how long the 4×4 can last in the ground.
How much does a 2×4 cost?
Lumber Prices Board Stud* 8′ 2×3 $2.87 2×4 $5.17 $5.17 2×6 $8.82 $8.82.
How much do 4×4 weigh?
Lumber Weight Chart Weight of Dimensional Lumber 3 x 14 2.5 inch x 13.25 inch 7.82 lbs 3 x 16 2.5 x 15.25 9.00 4 x 4 3.5 x 3.5 2.89 4 x 6 3.5 x 5.5 4.54.
What is board foot?
A board foot is a wood measurement for a piece of lumber 12″ wide by 1′ long by 1″ thick for estimating purposes. Learn how to figure total board feet in your next stack of lumber below.
How far apart should fence posts be?
Most fence posts can be spaced 8 to 12 feet apart. While this is a general criteria, it doesn’t cover all scenarios. For instance, high tensile fence can have larger spacing, requiring line posts every 15 to 20 feet for field fence styles, and as much as 20-30 feet for high tensile barbed and smooth wire.
How deep should a post be for a fence?
Dig post hole so diameter of the hole is 3 times the width of the post (i.e., the hole for a 4” wood post should be about 12 inches wide). The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet).
How long does pressure treated fence post last?
If properly treated and installed, pine fence posts can last for 20–35 years; untreated pine posts might only last 3–7 years. chemical in the posts. When large numbers of fence posts need to be installed it is probably most practical to pound them into the ground with a hydraulic post driver, small end first.
How much weight can an 8×8 post support?
That being said, a post can hold a tremendous amount of load! If a particular species of wood can support 1,000 psi, then an 8×8 post can hold 64,000 pounds! The limiting factor (reason to up-size) will likely be aesthetics and/or the number or type of joints needed.
How much weight can a 4×4 hold vertically?
Generally, you can expect a vertical 4×4 to support at least 4,300 pounds, but the amount of weight could be significantly higher than that in some cases. Even at 12 ft high, a vertical 4×4 made out of No. 2 Southern Pine will hold over 3,000 pounds.
How much does Southern yellow pine weight per board foot?
Weights of Various Woods (pounds per 1000 board feet) Species Lumber Wood Pine, slash 4,700 5,040 Pine, sugar 4,250 4,590 Pine, yellow (western) 3,750 4,050 Pine, white 2,920 3,150.
How thick is a treated 4×4?
After drying and planing, it will be 1 1⁄2 by 3 1⁄2 inches. These sizes have been jointly published in the National Institute of Standards & Technology Voluntary Product Standard PS 20-10 with support from the U.S. Department of Commerce for wood with a moisture content of 19% or less.
What is thickness of 4×4?
According to the NHLA rules, 13/16″ is the standard acceptable thickness of surfaced 4/4 lumber.
What are 4×4 lumber used for?
Good lumber, particularly for indoor projects such as bannisters, pillars or workbenches. These can be used outside but are not pressure-treated and would need to be painted or sealed if used in wet areas or they will rot quickly.
