Table of Contents

1 – 4 bags of concrete per fence post are typically what’s needed. This depends on the type of soil, fence design, height, post size and bag weight. In general the depth of the post’s hole needs to be 1/3 to 1/2 of the above ground height of the post.

## How many bags of concrete do I need for a post?

Most fence post holes will need between 1 – 4 bags of concrete to securely hold the post in place. The best way to determine the size of the hole is: Diameter of the hole is 3 times the width of the fence post. Depth of the hole is one-third to half the above ground height of the fence post.

## How many 50lb bags of concrete do I need for a fence post?

For reference, a 40-pound bag of concrete typically yields about 0.3 cubic feet, a 50-pound bag yields 0.37 cubic feet, a 60-pound bag yields 0.45 cubic feet, and an 80-pound bag yields 0.6 feet. This means that in the example above, each post would require about eight 50-pound bags.

## Is 2 feet deep enough for fence posts?

2 feet is the minimum depth that you should dig your fence post holes for. To dig the holes one-third to one-half of the post’s aboveground height, is a general formula. The deeper you dig the holes, the more stability your fence has.

## How much post mix do I need per post?

How much Post Mix do I need for a fence post? The exact amount of Post Mix Concrete needed will vary depending on the width and depth of the hole, but as a general rule you’ll need about one and a third bags for a standard fence post.

## What is the best concrete mix for fence posts?

For a small to mid sized job I recommend going with premixed. The best concrete mix for fence posts I’ve found is Quikrete Fast Setting Concrete Mix in a 50 lb bag. It’s 4000 psi, easy to work with, sets up fast, and doesn’t need to be mixed. Just pour it in the hole and soak with water.

## How many square feet does a 50 lb bag of quikrete cover?

Regarding this, how much does a 50 lb bag concrete cover?, as 133 lb concrete = 1 CF, so a bag of 50 lb concrete = 50/133 = 0.375 CF, therefore, a 50 lb bag of concrete approximately cover around 1.5 square feet area upto standard depth of depth of 3 inch for your patio and sidewalk.

## How big of a hole do I need for a 4×4 post?

The diameter of your post hole should be three times the diameter of your post. So, if you’re planning on using a four-inch round or 4×4-inch square post, your post hole will need to be 12 inches in diameter. For a six-foot-high fence post, we would need a hole that’s 36 inches deep and 12 inches in diameter.

## How many bags of cement do I need for 12×12?

of 40lb bag = 1.76 ÷ 0.011 = 160 bags. To determine how many bags of concrete you will need, divide the total cubic yards needed by the yields, at 5 inch thick, for a 12×12 slab you will need 2.22 yards of concrete, so number of 80lb bag of concrete = 2.22 ÷ 0.022 = 100 bags, No.

## Is cement required for fence posts?

Do Fence Posts Need To Be Set in Concrete? No, fence posts don’t need to be set in concrete, and there are plenty of other ways to fix your posts if this feels a bit too permanent. If you are using wooden posts, concrete may actually be the worst option.

## Is 18 inches deep enough for a fence post?

The general rule of thumb when setting a post is that the depth of the post’s hole needs to be one-third to one-half of the actual above-ground height of the post. So, a six-foot-high finished post ideally needs to be buried three feet into the ground.

## Can you put dry concrete in a post hole?

Fast-setting concrete is ideal for setting posts because there’s no mixing—you simply pour the dry concrete from the bag right into the hole, then add water.

## Is one bag of Postcrete enough for one post?

“Usually one bag of postcrete per post is enough, however you can use a two bags per post if you feel this is needed.

## How many posts will 1 bag of Postcrete do?

Just over one bag per hole should be sufficient, blue circle postcrete suggest 1 bag will fill a 8 x 30 inch hole with a 4×4 post. You’re dimensions are slightly bigger than that so better to be safe than sorry and have a bit extra.

## Can I use Postcrete on concrete posts?

A ready-to-use blend of selected sand, cement and additives formulated for fixing wooden, concrete and metal posts. To fix all types of wood, metal and concrete posts. Postcrete is ready to use. No mixing is required.

## How much sand and cement do I need for fence posts?

In terms of the ratio to use for a concreting fence posts, the best mix is a mix of 1:2:4 (1 cement, 2 sand, 4 aggregate). Concrete is always best mixed using a cement mixer to ensure it’s even, but if you only need to mix a little, hand mixing is ok (see mixing concrete project above for tips on how to do this).

## Can I pour concrete in a hole full of water?

The water in the hole under the pipe can be sucked out with a wet-dry vacuum before and during the repair job.