Table of Contents
Thompson’s WaterSeal includes a complete line of deck sealers and stains for protecting deck wood from moisture and sunlight. Applying a sealer and/or stain typically is recommended every one to three years, depending on the finishing product, deck use, weather conditions, and sun exposure.
How long does Thompsons Water Seal last for?
If applied correctly, Water Seal will last up to 4 years. This is dependent on conditions such as orientation of the wall and local climate.
How many coats of Thompson Water Seal do I need?
One coat is enough, but if more color is desired, a second coat can be applied within two hours before the first coat has dried. With Thompson’s® WaterSeal® Waterproofing Stains, you can clean your tools with soap and water.
Can you use too much Thompson Water Seal?
If over-application occurs and there is puddling of the product, redistribute product within 15 minutes to a dry area or wipe off. Q: Will the formula of Thompson’s® WaterSeal® Sport Seal® or Fabric Seal change the feel of the treated surface? No. These products will not change the surface’s feel or leave it sticky.
Will Thompsons Water Seal go bad?
The silicon-based sealer has a very long life when used, is a semi-permanent option, and is hard to remove once applied. Its shelf life is around five years.
Is Thompson water Seal any good?
– Thompson’s® WaterSeal® Clear did not alter or change the appearance of the wood. After full drying, we tested the ability to repel water. Water did bead on top of the finish and did not absorb into the wood. – As far as we can tell, Thompson’s® WaterSeal® does not prevent UV graying at all.
What is the best way to apply Thompson’s water Seal?
The fastest way to apply is with a pump-up sprayer (using a coarse setting), but you can also apply with a brush or a roller. You should apply liberally. In the case of areas with heavy discoloration or dirt, apply a second coat, brush lightly with a broom and hose off.
How many coats of water seal do I need?
Apply 2 coats using brush,roller or sprayer. note: Use at full strength.do not dilute. The second coat should be applied when the first coat has soaked in the surface. For best results do not leave the first coat to dry for more than 1 hour before applying the second coat.
How much area does a gallon of Thompson’s Water Seal cover?
Approximate Coverage Material Approximate Coverage (sq. ft./gal.) Wood: Rough Sawn 100 Wood: Smooth Finish 200 Plywood 150 Wood Shingles 100.
Does Thompson Water Seal need to be shaken?
Shake contents well before use. Shake or mix thoroughly before and occasionally during use. Only one light coat is necessary in most applications. Apply by brush, roller, dipping, or sprayer.
How do you remove Thompson’s water Seal from skin?
Soak your hands in warm water for about five minutes. This helps soften the skin and loosen the Seal-It. Dry hands on a towel, then rub a drop of hand lotion over the area with the Seal-It on it. Gently wipe off the lotion to remove the softened Seal-It.
Is Thompsons oil or water based?
Thompson’s® WaterSeal® Penetrating Timber Oil is an oil-based product that provides protection by penetrating into wood pores and sealing out water infiltration. Thompson’s® WaterSeal® Waterproofing Stains are water-based products that have film-forming properties to protect the wood by repelling water.
Can I mix stain and Thompson’s water sealer?
As long as it’s all oil based you should be able too. But if it’s a solid color stain it might turn a little transparent if mixed with the sealer..just give it a try on a scrap piece. Bingo. As long as they use the same solvents, it should be fine.
What is the best sealant for pressure-treated wood?
Best Deck Sealers for Pressure-treated Wood Ready Seal 520 Exterior Stain and Sealer for Wood. SEAL-ONCE Nano+Poly Ready Mix Penetrating Wood Sealer. #1 Deck Premium Semi-Transparent Wood Stain for Decks. Thompsons Waterseal Solid Waterproofing Stain. Eco Advance Wood Siloxane Waterproofer Concentrate.
What if it rains after sealing deck?
Rain will damage the finish of any wet sealer with linseed oil or mineral oil in it. Because it forms a coating, it takes several hours to dry, and during that time, the sealer is vulnerable. After the rain has passed and the deck has dried, take a closer look.
How do you Waterproof untreated wood?
There are three surefire ways to waterproof your wood for years to come. Use linseed or Tung oil to create a beautiful and protective hand-rubbed finish. Seal the wood with coating of polyurethane, varnish, or lacquer. Finish and waterproof wood simultaneously with a stain-sealant combo.
Is it better to stain or seal a deck?
Sealing a deck is best for cedar, teak, mahogany, or other quality woods as it enhances the wood grain and natural color. Staining a deck protects the wood from mold, mildew, moisture, and rot, and UV rays and sun damage.
Can you use a pump sprayer to apply Thompson’s Water Seal?
To apply Thompson’s water seal with a sprayer, you can use a garden sprayer with a hose or a pump sprayer. However, the manufacturer of Thompson’s water seal recommends that their product be used with a plastic sprayer and a brass wand.
Can you apply a second coat of stain after 24 hours?
It is important to wipe off the stain thoroughly and consistently (in the direction of the grain) to get an evenly stained surface. If a darker, or deeper color is desired, allow the first coat of stain to dry for 24 hours, then apply a second coat of stain in the same manner as the first.
How often should I water seal my fence?
While you should always follow the manufacturer’s recommendations, the general rule is that wood fences should be stained every five years and sealers should be applied every two to three.
Is Thompson Water Seal milky white?
Thompson’s Water Seal Advanced Natural Wood Protector goes on milky but dries clear.
Is it necessary to seal pressure treated wood?
However, most pressure-treated wood should have periodic sealing against moisture, preferably every year or so. Although the wood is resistant to rot and insect attacks because of the pressure treatment, it can warp, split and develop mildew if not protected from the effects of water.
What to do if you get Flex Seal on your skin?
If you get Flex Seal on them, it is best to remove it immediately with a dry paper towel. If you can’t remove it before it begins to dry, we recommend using a pumice soap such as LAVA soap to wash and remove it with warm water.
What is Thompson’s Water Seal used for?
Thompson’s Water Seal, offers superb weather protection for bricks, mortar, stone & concrete. Its advanced silicone micro emulsion soaks in deep to provide long lasting protection against rain damage.
What are active ingredients in Thompson’s Water Seal?
Chemical Composition/Ingredients Propane 000074-98-6 200-827-9 Butane 000106-97-8 203-448-7 Solvent naphtha, petroleum, medium aliphatic 064742-88-7 265-191-7 Distillates, petroleum, hydrotreated heavy paraffinic 064742-54-7 265-157-1 Solvent naphtha, petroleum, light aromatic 064742-95-6 265-199-0.
How long does Thompsons water Seal last for?
If applied correctly, Water Seal will last up to 4 years. This is dependent on conditions such as orientation of the wall and local climate.
How many coats of Thompson water Seal do I need?
One coat is enough, but if more color is desired, a second coat can be applied within two hours before the first coat has dried. With Thompson’s® WaterSeal® Waterproofing Stains, you can clean your tools with soap and water.
Can you use too much Thompson water Seal?
If over-application occurs and there is puddling of the product, redistribute product within 15 minutes to a dry area or wipe off. Q: Will the formula of Thompson’s® WaterSeal® Sport Seal® or Fabric Seal change the feel of the treated surface? No. These products will not change the surface’s feel or leave it sticky.
How often should you seal your deck?
You should reapply wood sealer at least every three years. In many cases, you need to seal a wood deck once a year. The more foot traffic and sun exposure your deck gets, the more often you need to apply deck sealant.
Is Thompson water Seal any good?
– Thompson’s® WaterSeal® Clear did not alter or change the appearance of the wood. After full drying, we tested the ability to repel water. Water did bead on top of the finish and did not absorb into the wood. – As far as we can tell, Thompson’s® WaterSeal® does not prevent UV graying at all.
What is the best way to apply Thompson’s water Seal?
The fastest way to apply is with a pump-up sprayer (using a coarse setting), but you can also apply with a brush or a roller. You should apply liberally. In the case of areas with heavy discoloration or dirt, apply a second coat, brush lightly with a broom and hose off.
How many coats of water seal do I need?
Apply 2 coats using brush,roller or sprayer. note: Use at full strength.do not dilute. The second coat should be applied when the first coat has soaked in the surface. For best results do not leave the first coat to dry for more than 1 hour before applying the second coat.
How much area does a gallon of Thompson’s Water Seal cover?
Approximate Coverage Material Approximate Coverage (sq. ft./gal.) Wood: Rough Sawn 100 Wood: Smooth Finish 200 Plywood 150 Wood Shingles 100.
How long does Thompson water Seal need to dry before rain?
Allow at least 48 hours to dry; however drying time will vary depending on the substrate, temperature, and humidity.
How do you remove Thompson’s water Seal from skin?
Soak your hands in warm water for about five minutes. This helps soften the skin and loosen the Seal-It. Dry hands on a towel, then rub a drop of hand lotion over the area with the Seal-It on it. Gently wipe off the lotion to remove the softened Seal-It.
Is Thompsons oil or water based?
Thompson’s® WaterSeal® Penetrating Timber Oil is an oil-based product that provides protection by penetrating into wood pores and sealing out water infiltration. Thompson’s® WaterSeal® Waterproofing Stains are water-based products that have film-forming properties to protect the wood by repelling water.
Is it better to stain or seal a deck?
Sealing a deck is best for cedar, teak, mahogany, or other quality woods as it enhances the wood grain and natural color. Staining a deck protects the wood from mold, mildew, moisture, and rot, and UV rays and sun damage.
Do you need to seal your deck every year?
A standard wooden deck typically requires annual resealing, but depending on the above factors, you may only need to reseal every 2-3 years. A properly-sealed deck should cause the water to bead up. If your water gets absorbed into the wood, it’s time to retreat your decking to prevent damage and rot.
Should I seal my deck every year?
For most decks, sealing once each year is a good rule of thumb. Depending on the condition of your deck this can be adjusted, but keep in mind that you should never go beyond three years maximum before re-sealing and staining.
Should I use Thompson Water Seal on pressure-treated wood?
Although the wood is resistant to rot and insect attacks because of the pressure treatment, it can warp, split and develop mildew if not protected from the effects of water. The directions for some, such as Thompson’s Water Seal, specify pressure-treated wood as a suitable use.
What is the best sealant for pressure-treated wood?
Best Deck Sealers for Pressure-treated Wood Ready Seal 520 Exterior Stain and Sealer for Wood. SEAL-ONCE Nano+Poly Ready Mix Penetrating Wood Sealer. #1 Deck Premium Semi-Transparent Wood Stain for Decks. Thompsons Waterseal Solid Waterproofing Stain. Eco Advance Wood Siloxane Waterproofer Concentrate.
Can you use a sprayer to apply Thompson’s water Seal?
Answer: The manufacturer of Thompson Water Seal recommended that you use their product with a plastic sprayer with a brass wand, such as our Chapin Premier sprayer. Once you are done with the product, it is recommended that you run mineral spirits through the sprayer and then water to clean it.
Can you use a pump sprayer to apply Thompson’s water Seal?
To apply Thompson’s water seal with a sprayer, you can use a garden sprayer with a hose or a pump sprayer. However, the manufacturer of Thompson’s water seal recommends that their product be used with a plastic sprayer and a brass wand.
Can I use Thompson’s Water Seal on concrete?
Provides proven waterproofing protection for all masonry surfaces including pavers, brick, concrete, stone, stucco, clay and quarry tile. Use for concrete waterproofing and as a brick sealer.
Can you apply a second coat of stain after 24 hours?
It is important to wipe off the stain thoroughly and consistently (in the direction of the grain) to get an evenly stained surface. If a darker, or deeper color is desired, allow the first coat of stain to dry for 24 hours, then apply a second coat of stain in the same manner as the first.
How often should I water seal my fence?
While you should always follow the manufacturer’s recommendations, the general rule is that wood fences should be stained every five years and sealers should be applied every two to three.
Is Thompson Water Seal milky white?
Thompson’s Water Seal Advanced Natural Wood Protector goes on milky but dries clear.
