How Open Lock Without Key

How do you unlock a lock without a key?

A butterknife can also be used to pick the lock in place of paper clips or a lock-picking set. By inserting the knife blade into the lock as far as it goes and applying pressure in different directions, you may be able to pop the lock open.

How do you force a lock to open?

One of the easiest ways to break a padlock is with a hammer. Start by inserting 2 fingers into the padlock’s shackle loop and pull up on the shackle to create tension. Then, tap the side of the lock that contains the fixed end of the shackle with a hammer using quick, short strikes.

How do you break a padlock without tools?

The Different Ways on How to Break a Padlock without Tools Shimming It. If you think you’re not good at picking, try shimming it. Hitting It with a Hammer. You can use a hammer to crack the padlock. Using a Canister with Compressed Air.

Can you open a lock with a bobby pin?

Bobby pins will work on most doorknob locks, ie, locks where you insert the key into the doorknob, commonly found in interior rooms. Insert the two points of the bobby pin into the lock. Press the bobby pin forward into the lock— depending on the door, simple forward pressure can be enough to open the lock.

How do you pick a lock with a screwdriver?

To unlock a privacy lock you’ll need a flathead screwdriver that is small enough to fit into the hole on the doorknob. Insert your screwdriver into the hole and push forward. If your doorknob is using a push-button type privacy lock, then you should hear a loud click and the door will open.

How do you open a lock with a hammer?

What to Do Step 1: Prepare the hammer and wear your gloves and goggles. Step 2: Place your fingers into the shackle loop and pull to create tension. Step 3: Pound the side of the padlock with a hammer again and again until you successfully bump the lock to open. Step 4: Reuse the lock if it is still working.

How do you get a padlock off?

How to Open a Padlock without a Key Step 1: Insert the tip of the screwdriver inside the keyhole until it reaches the barrel of the lock. Step 2: Thrust the screwdriver in and out of the lock while jiggling it. Step 3: Continue to shake the lock until you hit the tumblers and you open the lock.

Can bolt cutters cut a padlock?

Bolt cutters are the common tool of choice for to cut padlocks during forcible-entry. You will find that most of the time, a set of bolt cutters will make the cut, using a big effort, but the damage to the tool after continual use will render it ineffective over time.

How do you pick a simple lock?

The easiest way to pick a lock is to use the fast and dirty method: scrubbing. Insert Tension Wrench into the Bottom of Key Hole and Apply Slight Pressure. Insert Pick at Top of Lock. While Applying Slight Torque to Your Wrench, Scrub Your Pick Back and Forth in the Key Hole. Repeat Until All the Pins Set.

Can you pick a lock with a paper clip?

Picking a lock with paper clips works pretty much the same way as picking a lock with a traditional tension wrench and rake. You just need to turn two paper clips into those two very same tools, and then pick the lock with them like you’d normally do.

Can you pick a lock with a pencil?

What Can a Pencil Do for Locks? When a lock needs some sort of lubrication to work smoothly, professional locksmiths tend to choose powdered graphite. However, you may use a pencil as a cheaper substitute for graphite.

How do you pick a deadbolt with a knife?

Method 1: Stick And Wiggle Step 1: Start inserting the knife as deep into the door lock as possible. Step 2: Apply light pressure on your knife as if you are turning a normal key. Step 3: Gently rock the knife in an up and down motion, simultaneously, move it in and out of this lock.

How do you open a deadbolt without a key?

One of the best-known ways to unlock a deadbolt without a key is by using two bobby pins. Start by inserting the closed “looped” side of one bobby pin into the bottom portion of the lock. Use the second bobby pin, broken in half, toward the top of the lock and move it back and forth.

How do you open a locked window with a knife?

Find the place where the door or window locks. Clean the line of knife and try to open the latch by passing the latch inside. Slide the knife between the door and the frame of the door. Slide until you touch the bolt.

Can you break a lock with a hammer?

Breaking a Master Lock Is Insanely Easy Turns out, any Master Lock can easily be broken into with just a small hammer. As this video illustrates, all you need to do is tap the side of a Master Lock with a hammer to get it to open, no key, no combination required.

How do you break a hardened steel padlock?

Hold the grips on your cutters and apply firm pressure to break through the lock. Squeeze the handles together until it cuts through the shackle. If you can’t cut through the lock yourself, ask a friend to help you close the bolt cutters. If the lock is made of hardened steel, bolt cutters may not work.

Can you cut a padlock with a hacksaw?

If you misplace your key or forget the combination to a lock, you may need to cut through the lock to get it back. Most steel locks can be opened by either using bolt cutters, an angle grinder, or a hacksaw.