Table of Contents
Thickness: 33 mils (20ga), 43 mils (18ga), 54 mils (16ga), 68 mils (14ga) and 97 mils (12ga). 33mil (20ga) and 43mil (18ga) framing products are produced with 33ksi steel. 54mil (16ga), 68mil (14ga) and 97mil (12ga) products are produced with 50ksi steel unless otherwise noted.
How thick are metal stud walls?
Metal Stud Sizes The most common size stud is a 3 5/8″ wide stud. Combined with a layer of 5/8″ gypsum wall board on both sides will give a 4 7/8″ thick wall.
What size metal studs are there?
Standard lengths are 10′, 12′ and 14′. Other lengths available upon request. Conventional metal studs are available in 25, 22, 20, 18, and 16 gauge steel for your convenience (1-5/8″ available in 20, 22 and 25 gauge only).
What is the actual size of a 2×4 metal stud?
Thus a metal stud taking the place of a two-by-four measures 1 5/8 by 4 inches, and a two-by-six, 1 5/8 by 6 inches — slightly fatter but the same depth as their wood equivalents.
What gauge are structural metal studs?
Most contractors are familiar with the light-gauge steel studs and track you can buy at lumberyards and drywall supply houses. These studs are usually 25-gauge steel with 1 1/4-inch flanges and are intended for non- load-bearing applications such as partition walls.
How thick is a 16 gauge metal stud?
Thicknesses and Coatings Steel Framing Thickness Table Designation Thickness (mils) Minimum Thickness (in) Reference Only Gauge No 43 0.0428 18 54 0.0538 16 68 0.0677 14.
How thick is a 20 gauge metal stud?
For example, 20-gauge interior wall partition studs have a thickness of 0.76 mm (30 mil), while 20-gauge structural studs have a minimum thickness of 0.84 mm (33 mil).
How wide is a 6 inch metal stud?
How wide is a 6 inch metal stud? A 6 inch metal stud measures 6 inches on its long face. This equated to 1 5/8 by 4 inches.
How thick is a 6 metal stud?
For instance, ClarkDietrich labels 6-inch, 16-gauge studs with CD600S162-54 50 KSI. This tells you the stud is 6 inches wide with a 1-5/8 inch (1.62 inch) flange and is 16-ga (54 mils) thick. Finally, it shows the steel strength to be 50 ksi.
How thick are steel frame walls?
Steel wall frames are also typically 70mm or 90mm deep, and additional strength is achieved by using thicker gauge steel or additional folds or bends in the cross-section.
Is metal studs cheaper than wood?
Cost-effective: While never as cheap as wood, steel studs are now only about 30-percent more expensive than wood studs. Lightweight: Steel studs are lighter to carry and store than wood because they are hollow.
How thick is a steel frame?
Framing members are generally produced in a thickness of 12 to 25 gauge. Heavy gauges, such as 12 and 14 gauge, are commonly used when axial loads (parallel to the length of the member) are high, such as in load-bearing construction.
Are metal studs better than wood studs?
Metal studs are also healthier than wood studs because metal does not emit VOCs. Wood has several advantages over metal studs. Wood studs are less expensive and more available than metal studs. Wood studs are also easier and safer to cut, maintain, and repair, over metal studs.
Are metal studs load bearing?
Lighter gauge metal studs are used in non-load bearing applications such as some interior walls, half-walls, and partitions. Metal studs are available in many of the same basic dimensions as wood studs. Metal studs are usually mechanically fastened with screws.
What gauge steel is 33 mil?
These studs and track are manufactured from mill certified galvanized steel and are designed for use in curtain-wall and load bearing applications. Thicknesses range from 33 mils (20 gauge) to 97 mils (12 gauge).
What gauge are load bearing metal studs?
Most load-bearing walls require 16 or 18-gauge studs and interior walls are built using 20 or 25-gauge metal studs.
Can you mount a TV on metal studs?
Most TV mounts in the market are designed to be installed in either wooden studs or concrete, but it’s also possible to mount a TV into metal studs. The process is virtually the same, but you will need a few additional tools and equipment.
What is stronger 20 gauge or 25 gauge?
Liner Gauges The gauge represents the thickness of the liner, which is measured in millimeters. A 20 gauge swimming pool vinyl liner would be thinner than a 25 gauge vinyl liner, for example, with 20 gauge and above pool liners going into in-ground pools.
Which is thicker 18 or 20 gauge?
The word gauge with a number by it refers to the thickness of the metal used in constructing the casket. The smaller the number the thicker the steel. 18 Gauge would be a stronger metal than a 20 Gauge.
How thick is 25 gauge studs?
Nominal Gauge2 Minimum Thickness3 (Inches) Maximum Design Thickness4 (Inches) 26 0.0163 0.0172 25 0.0179 0.0188 22 0.0269 0.0283 20 0.0329 0.0346.
How wide is a 4 metal stud?
A 2×4, for example, is really 3-1/2″ x 1-1/2″. Metal framing on the other hand, is referenced by actual size. As a result you will get exactly what you order. If you request a 3-5/8″ steel stud, you will receive a full 3-5/8″ width.
How far apart are steel studs?
They’re always spaced either 16 or 24 inches on center (measured from center to center) along the wall and run between the floor and ceiling.
Is steel framing stronger than wood?
Overall, experts say steel and wood studs are cost-competitive, according to www.thespruce.com. As the technology evolves, metal framing has gotten stronger while also getting lighter in weight. Steel framing is not flammable, but wood framing is combustible.
