Table of Contents
Most manufacturers offer composite decking boards in 12′, 16′ and 20′ lengths. The width varies by brand and style and can range from one to two inches thick and four to six inches wide.
How thick is Trex composite decking?
The actual Trex decking boards are available in 1 or 2 inch thick boards. The three main types of boards are the Fascia, Grooved Edge and Square Edge. The Fascia is available in either 8 inch or 12 inch long boards. The boards are 0.75 inches thick and 11.375 inches wide.
What is the standard thickness of decking?
NOTE: Standard boards are often called a 5/4 board when referring to traditional lumber, which means the actual thickness is typically somewhere between 1” and 1 ¼”. Thicker boards are often called a 2 x 6 when referring to traditional lumber, which means the actual thickness is somewhere between 1.2” and 1.5”.
What are standard size composite deck boards?
Composite deck boards are typically offered in 12-foot and 16-foot lengths. Some brands, like Trex, feature a 20-foot deck board length which can be specially ordered.
What is the actual thickness of a 5 4 deck board?
Comparing 5/4 Decking With 2×6 Deck Boards, Pros and Cons 2×6 Deck Boards 5/4 Decking Thickness 1 ½” (38mm) 1″ (25mm) Joist Spanning 24″ (600mm) 16″ (400mm) Weight 2.36 lbs (1.07kg) lnft* 1.59 lbs (0.72 kg) lnft* Profile cut Square Cut Rounded Radius Edge.
Do they make a composite 2×4?
Armadillo Composite Decking 2x4s with capped radius edge provide the strength and durability needed for any project. Available in six stylish colors, our Composite 2x4s complement your deck and add the look of natural beauty without sacrificing quality.
How many deck boards do I need for a 10×10 deck?
For a 10×10 square deck, you would therefore need twenty-two 10′ deck boards. Dimensions for deck boards can vary depending on the look you want and the deck board type you use. However, the most common is a 5/4” thick by 6” wide deck board of any length.
Can I use 1×6 for decking?
Never use 1×6 or 5/4×6 material in close to ground applications. Spacing between boards: You must allow space for your deck boards to expand when they take on moisture, as they will inevitably do when exposed to wet weather, rain or high humidity.
How thick should patio decking be?
The most commonly used thickness for deck construction is 1-1/4”. But you can also get boards 2” thick, while there are boards only ¾” thick. It depends on the material, how flexible it is, and its hardness rate.
What is the most common deck board size?
The most common or standard deck board width is 6-inch wide planks based on square-foot coverage, labor, and material cost.
How thick is a 1×6 deck board?
1×4 and 1×6 boards lose 1/4 inch in thickness and 1/2 inch in width before leaving the mill. That means a 1 x 4 board is actually 3/4 inches by 3 1/2 inches. The larger 1x boards (1×8, 1×10, etc.).
What is a 5 4 inch board?
5/4 means approximately 1-1/4″ thick. 6/4 means approximately 1-1/2″ thick. 8/4 means approximately 2″ thick.
How much space do you need between composite deck boards?
One of the most critical steps for properly securing composite decking in place is to make sure you have a 1/4-inch to 3/16-inch gap between the decking boards (don’t exceed 1/2 inch). This space is important for two reasons.
Why do they call it 5 4 decking?
Quarters refer to the thickness of rough-sawn lumber measured in ¼-inch increments. Instead of reading it as a fraction, it should be read as a number of quarters: 5/4 is five quarters, 4/4 is four quarters, etc.
How thick is a treated deck board?
CHOOSING THE RIGHT DECKING BOARD THICKNESS Decking Type Actual Thickness (inches) Suggested On Center Joist Spacing (inches) Tropical Hardwoods 1x 13/16” 16” Thermally-Modified 5/4 1” 16” Pressure Treated Pine 5/4 1” 16” Western Red Cedar 5/4 1” 16”.
Can I use 2×6 for deck boards?
Wood decking is commonly available in 2×6 and 5/4 x 6 profiles. 5/4 x 6 is produced specifically for decking and is milled with a radius edge or bull nose. 2×6 is thicker and is stronger, but is also more expensive. Spacing between deck boards provide a few critical functions.
What is a composite 2×4?
2×4 board is made of high-performance composite that won’t rot, warp or splinter, unlike wood. 2×4 has a protective outer shell for durability; resists fading and staining.
Does Trex make 2x4s?
Trex Transcend 2×4 and 2×6 Lumber 2x composite boards to match Trex Transcend decking for railings and special applications. Shell covers top and sides (3 sides) 16′ length.
What is the longest Trex board?
2 x 6 boards available in 12′, 16′, and 20′ lengths. Only available in Transcend Tropicals.
How much does it cost to build a 20×20 deck?
The average homeowner spends $2,200 to build a 10×10 foot deck, $6,160 to build a 14×20 deck, and $8,800 to build a 20×20 deck. The cost to build a deck with pressure-treated wood, hardwood, or composite is about $25 per square foot, for both materials and installation.
How many Trex boards do I need for a 12×12 deck?
(Choose from 8, 12, 16, or 20 ft board lengths. Choose which board best fits the dimensions of the deck.Decking Materials. Board length Boards required 8 FT 206 12 FT 137 16 FT 103 20 FT 83.
What material do I need for a 12×12 deck?
You will need 18 boards of 2-by-6-inch lumber or nine 2-by-10 inch boards to build the joists, also known as the beams. You should purchase an additional 25 percent wood to allow for framing pieces and waste.
