Table of Contents
Fiber cement siding can be nailed by hand or with a pneumatic nailer. It can also be attached using corrosion resistant screws. Use hot-dipped galvanized or stainless steel nails. Nails should penetrate through the sheathing and at least 1” into studs.
How do you nail fiber cement siding?
What kind of screws do you use for fiber cement siding?
Fasteners must be corrosion resistant, galvanized or stainless steel. James Hardie prefers and recommends installation of HardiePlank® lap siding by the blind nailing technique, such that fasteners are hidden by the course above. Fasteners shall be installed between 1 in. and 3/4 in.
How do you secure cement board siding?
Fasten the siding – You can fasten it with a pneumatic nailer or nailing by hand. You can use corrosion-resistant screws, or you can use stainless steel or hot-dipped galvanized nails. You can nail the siding by either blind nailing it at the top or face nailing it at the bottom.
Can you drill into fiber cement siding?
It can be cut and drilled just like wood. However, drilling through cement-fiber siding goes better if you use a carbide drill bit, as opposed to a regular steel drill bit. Cement-fiber siding can be drilled while installed on a house or prior to installation. Otherwise, the board siding may snap during drilling.
Do you nail or screw Hardie board?
What is the correct fastener pattern for installing HardieBacker® cement board? Fasten HardieBacker sheets with proper nails or screws (as listed in ”Materials Required” in the backer installation instructions) every 8” around the perimeter and all supporting studs.
Can you use screws for fiber cement siding?
Nail Fastening Fiber Cement Siding You can fasten fiber cement with roofing nails, as well as select versions of screws, siding nails, and common nails. You can use electroplated fasteners, but it’s better to use stainless steel or hot-dipped galvanized fasteners.
What fasteners do you use with Hardie board?
Fasteners must be corrosion resistant, galvanized or stainless steel. Electro-galvanized nails are acceptable for use with James Hardie Siding Products, but may exhibit premature corrosion. James Hardie recommends the use of quality, hot-dipped galvanized nails.
What is the best fastener for Hardie board?
Fasteners must be corrosion resistant, galvanized, or stainless steel. Electro-galvanized are acceptable but may exhibit premature corrosion. James Hardie recommends the use of quality, hot-dipped galvanized nails.
How do I screw into Hardie board?
Drill pilot holes, at each mark, one-quarter to one-half inch deep, to make it easier to insert screws and prevent cracking the siding. Align the bracket holes with the pilot holes in the siding. Insert the screws and tighten securely using a drill with screwdriver bit attached. Hang the basket on the bracket.
How do you attach cement board?
Drill a small hole in one end of a scrap of wood, attach it to the cement board at the center of the circle, screwing through the cement board into the work surface below. Then screw in a “cutter” screw where you want the circle to be scored, for example, 2 in. from the center for a 4-in. hole.
How do you cut a hole in fiber cement siding?
Cement fiber siding (CFS) can be drilled, nailed and cut much like wood. Since it is more abrasive than wood, carbide or diamond blades are best for cutting. Holes are easy to make with an electric drill and a carbide tip drill bit. As with any project, good eye protection is recommended.
Can you hammer a nail into Hardie board?
Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun. Don’t drive nails into the siding at an angle.
Is fiber cement siding expensive?
Fiber cement siding costs $5 to $25 per square foot, including materials and labor. The price for materials equals $1 and $15 per square foot. The labor cost ranges from $4 to $10 per square foot.
What type of nails do you use for Hardie board siding?
James Hardie recommends the use of quality, hot-dipped galvanized nails. James Hardie is not responsible for the corrosion resistance of fasteners. Stainless steel fasteners are recommended when installing James Hardie® products near the ocean, large bodies of water, or in very humid climates.
Can I use liquid nail on cement board?
LN-907 Liquid Nails is recommended for cement board and most other common building materials. The application temperature is from 22 to 120 Fahrenheit and the service temperature is -20 to 140 degrees Fahrenheit. This makes it ideal for just about any DIY project and on most construction projects.
Will cement board hold a screw?
Cement board attached to plywood or similar underlayment will hold with only 1 1/4-inch screws; for thick or heavy metal fixtures, use 1 5/8-inch screws. In general, 1 1/2-inch galvanized nails will hold the board firmly in place. Even if you use this extra adhesive, you should still apply the nails or screws.
Does it matter which side of cement board faces out?
No, it doesn’t matter. Regardless of which side faces out during installation, you can expect the same great performance that has made USG Durock® Brand Cement Board the preferred choice of professionals and do-it-yourselfers for decades.
