QA

How To Backwash A Pool Pump

How do I backwash my pool?

How often should you backwash your pool pump?

“When do we need to backwash?” – It is recommended to backwash your filter once every 4-6 weeks of regular use. Additionally, there are several instances that would require backwashing in between the normal monthly backwashing.

What is the purpose of backwashing a pool filter?

The process of backwashing dislodges trapped debris and contaminants, flushing them out through your value’s waste line or a hose that is connected to the pool pump. When the filter media is clean, the pressure gauge is lower and water can easily flow in and out of the system.

How long do I backwash my pool?

Turn off the pool pump. Set the sand filter valve handle to the BACKWASH pool position and ensure the handle locks in place. Turn on the pump and backwash for 2 minutes or until the water in the sight glass (located on the filter) is running clear.

Does backwashing remove water from pool?

The backwashing process reverses the flow of water to flush out contaminants from a swimming pool filter. It should be carried out until water runs clear through the waste line.

Should sand come out when I backwash?

In general, you shouldn’t be losing sand from your sand filter. Nor should any sand be coming out during backwashing, rinsing or filtering.

Where does the backwash water go?

Any backwash water is to bypass the septic tank and be discharged to the drain between the septic tank and the common effluent drain.

Can you backwash a pool too much?

Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.

Does backwashing remove algae?

Use a vacuum or backwash the pool to remove the dead algae. Apply a mustard algaecide following the label directions. Allow the water to circulate for 24 hours. Use a pool vacuum or backwash the pool again to remove the remaining dead algae.

Does backwashing clean the filter?

One way to keep your swimming pool’s filter system in working order is through the use of backwashing, or reversing the flow of water through the filter to remove any built-up contaminants. above the clean pressure, it’s probably time to routinely clean the pool filter.

How often should you backwash?

As a general rule, you should be backwashing your pool about once a week or in conjugation with your scheduled maintenance. Another industry standard is to backwash when your filter’s pressure gauge reads 8-10 PSI (pounds per square inch) over the starting level or “clean” pressure.

Can you backwash with filter balls?

Yes, you save water with FilterBalls with the backwashing. Simply follow the FilterBalls installation instructions by noting your filter pressure upon installation and backwash when the pressure increases by 5-6 psi. Note your starting pressure will be much lower than what you experienced with sand.

How long do you backwash de filter?

Backwashing a sand or DE filter is a simple task. Shut off the pump, set the multiport valve or slide valve handle to the backwash position, roll out the backwash hose and turn the pump on again. Backwash for 3-4 minutes or until the water runs clear, then shut the pump off and return the valve to the filter position.

How much water do you lose when you backwash a pool?

The backwashing of a typical Olympic-sized pool results in the loss of about 6,300 gallons of water per backwashing cycle, according to Recreation Management. As a result, don’t add chemicals to your water until after you’ve backwashed — otherwise, you’re just throwing money down the drain… literally.

How much water does it take to backwash a pool filter?

Backwashing can take only a few minutes to complete, but for a typical pool, it consumes approximately 200 to 300 gallons of pool water! So, while your filter is losing unwanted dirt and debris—your pool is losing a ton of water.

Do you have to backwash an above ground pool?

According to the Centers for Disease Control, poor water quality can lead to the spread of germs and even cause illness. To ensure that the water in your above-ground pool is filtered thoroughly, you must periodically backwash it.

How do you backwash a small Intex pool filter?

How to Backwash an Intex Pool Turn the pump filter off. Set the filter to back-wash. Connect a hose or pipe to the discharge port. Turn on the filter. Turn off the filter and set the filter mode back to its regular position. Disconnect the hose from the discharge port and store the hose.

Why am I getting sand in my pool after I backwash?

Your pump may be too large or the sand level too high in the filter. When the filter is backwashing the water flow can cause the sand to rise high enough and overflow into the standpipe, which will allow the sand back into the pool.

Why is sand coming out of my sand filter?

Sand coming from the pool filter is the sign of a broken component in the filter. If you see it blowing out into the pool, something is broken. The most common problem is a cracked lateral, which is one of the perforated pipes at the bottom of the filter that catches water that has circulated through the sand.

What happens if you backwash too long?

Backwashing a filter too frequently will keep the sand so free of dirt buildup that it will not have the ability to remove the smaller particles of dirt and they will simply pass through sometimes causing cloudiness in water.

What PSI should my pool pump run at?

If anything could be considered “normal”, it would be about 10 psi. Most filter systems are designed to operate in the 5-15 or 10-20 psi range. The way to find out your particular correct pool filter pressure is to clean or backwash the filter thoroughly and empty the pump and skimmer baskets.