Table of Contents
Can you make your own shower pan?
These days, if you want to put in a shower, you can just go to a home center and pick up a fiberglass unit. So if you’d like to install a tile shower and are willing to build your own custom shower pan, you’ll be able to tile it to match the walls. And with a mortar and tile floor, your shower can be any shape.
Can concrete be used for shower floor?
Concrete is perfectly adequate, if not recommended, for use as the shower pan base for materials such as stone, tile or mosaic tile to be used as the finish surface (as long as there is a proper membrane between the concrete and any vulnerable surrounding material).
How thick should a shower pan be?
The shower pan base mortar layer should be about an inch thick. The shower floor already has a pre-slope, so just apply a base mortar layer that is even thickness throughout the shower floor area.
What kind of cement do you use for a shower pan?
The ideal mortar for a shower pan is a mix of standard cement mix with sand and Portland cement. This type of mortar creates a great water-resistant barrier that can support the weight of the shower unit.
What material do you use for a shower pan?
Shower pans are typically made out of four different types of materials: acrylic, fiberglass, custom tile and composite. Acrylic: While shower pans made from acrylic are typically reinforced with other materials, they are largely made of large sheets of acrylic that have been heated and stretched onto a mold.
Do you need a shower pan liner on concrete floor?
It will need to be lined or it will wick into the slab and studding. The liner also makes the walls around the pan water-tight, that’s why the liner normally goes up at least 3″ above the pan behind the tile and backer material. Moisture gets behind the wall tile and is eventually caught by the liner.
Can you use quikrete for shower pan?
The best concrete mix for shower pans is made by Quikrete. They make two products, the first is called Floor Mud, the 2nd is their Sand/Topping mix. Both work great for building a shower pan. Just like other types of concrete mix, there are DIY options.
What is the difference between a shower pan and a shower base?
What Do They Do? While a shower pan and a shower base both channel water into the drain, there’s one key difference: “Shower pan” is the actual shower floor that you step on, whereas “shower base” refers to the structure underneath the shower itself.
How thin can a mortar shower pan be?
Thin-set mortars are typically about 3/16”, which makes it preferred when height is an issue (e.g. barrier free showers). When tile is bonded to the subfloor with a thin-set, movement in the subfloor can telegraph through the tile and cause it to crack.
How far up the wall should a shower pan liner go?
The pan liner should finish a minimum of 6 inches above the framed or (roughed-in) curb height. This height allows for the application of concrete base and finishes to be applied.
How many bags of sand do I put in a shower pan?
I usually mix one bag sand/topping mix with a half bag of sand (25lbs) to make things easy and have had good luck with that. Be very careful with how much water you add to the deck mud as you mix it up. It’s referred to as dry-pack mortar for a reason. Do not add water like you are mixing concrete.
Do you need to waterproof under a shower base?
DON’T ignore the importance of waterproofing when installing an acrylic shower base. The walls and the area around the top of the acrylic base along the wall are very important for proper waterproofing and it is essential that it be done correctly. In a bathroom, proper waterproofing is non-negotiable.
How do you waterproof a concrete shower floor?
The most common technique is to apply multiple coats of a penetrating sealer like a water-based polyurethane. Fautch uses epoxies or two-part polyurethanes, sometimes both — epoxy as primer with polyurethane on top.
Does shower pan liner go behind backer board?
The wallboard must be installed 1/8 inch above the shower pan. If the shower pan is not in place, the wallboard height must be guessed, which can lead to inaccuracies and an expansion gap that is too large or too small.
What’s the best mortar mix for shower pan?
The best mortar for shower pans is a mixture of sand and Portland cement as it creates a water-resistant barrier that can support the weight of the shower unit and the users. You can create your own with Portland cement and fine sand (1:5) and 4 quarts water for 80 lb. of the mixture.
Can I use high strength concrete mix for shower pan?
You can use Quikrete for a shower pan but only if it is a sand mix. Floor Mud is ideal for shower pans because it does not sag and it can cure quickly. Be careful because Quikrete Floor Mud is not waterproof and you have to mix it carefully.
Can you use thinset for shower pan?
Mix thinset mortar with the drill and paddle. Add more thinset to one side to level the floor, if necessary. Check the floor to ensure it is level, using the carpenter’s level. Set the acrylic shower pan in place on top of the mortar.
What type of shower base is best?
The Best Materials for a Shower Base Acrylic shower bases are a popular choice. Acrylic is an extremely durable material that holds up well under pressure from weight and running water. Fiberglass shower bases are another common choice. Tiles offer a beautiful finish to your shower base.
