QA

Quick Answer: How To Clean Nutribullet Blade

How do you deep clean a NutriBullet blade?

How to clean nutribullet blades? Wash your blades by hand with warm, soapy water and a dish brush to loosen any stuck-on debris. If you want a deeper clean, rinse the blade with a 10% dilute vinegar and water solution or lemon juice.

Can you wash the NutriBullet blade?

THE NUTRIBULLET CUPS CAN BE WASHED ON THE TOP RACK OF THE DISHWASHER USING THE NORMAL (NOT SANITIZE) CYCLE. THE NUTRIBULLET CUPS AND BLADES SHOULD NOT BE IMMERSED IN BOILING WATER FOR ANY REASON AS THIS WILL WARP THE PLASTIC AND DAMAGE THE GASKET. SIMPLY HAND WASH THE BLADES IN WARM, MILD SOAPY WATER.

Can you remove the blade from NutriBullet blender?

Do not remove the easy-twist extractor blade from the NutriBullet® cup until blending has completely ceased. Do not use the easy-twist extractor blade as a storage lid for your cup.

Why is brown liquid coming out of my NutriBullet?

If you do not replace your blade you will run into the issue of the black/oil/tar looking gunk that comes out of the bottom of the blade unit. When this stuff cakes up in your blade gears it stops the blade from running smoothly and when it pushes against the motor (not running smoothly) the black gunk starts to burn.

How do you lubricate a blender blade?

Inspect around its base (and around the cutter shaft) for any built-up food residue. If the blades still do not turn, it’s probably either the switch or the motor. If the cutter shaft sticks, remove the jug, turn it upside down, and spray a lubricant (like WD-40) over the blades.

Why is my NutriBullet blade not spinning?

Prolonged use of the blender can cause the motors to wear out quickly, which can cause the blades to stop spinning. Unplug the NutriBullet blender and let it rest for a few minutes. Then, plug the blender back in and try to use it, again, making sure not to leave the blender running for more than one minute at a time.

How often should you replace NutriBullet blade?

How often do blades need replacing? To keep your nutribullet operating in tip-top condition, we recommend replacing your blades every 6 months.

How do you open a stuck NutriBullet?

Unplug the unit. Turn the unit upside down (with the cup still attached) As the entire unit is upside down, tap the top of the cup gently on the ground a few times. Twist the cup counter-clockwise and it should pop right out.

Why does my NutriBullet smell?

3 Answers. The blade assembly can fail and does not rotate freely, then you get additional friction overloading the motor, hence the smell and smoke.

Why does my NutriBullet smell bad?

plastic burning smell emitted. Chunks of plastic remain in the engine base docking area. Brown liquid in the base area. If all of these are happening then the cause is that your blade was probably submerged in water at some time with heat.

Does NutriBullet have a lifetime warranty?

nutribullet available extended warranty warrants nutribullet® products against defects in materials and workmanship for a period of three (3) years beyond the date of the expiration of the one-year limited warranty that comes with the nutribullet® free of charge.

What do you soak blender blades in?

We’ve found that a blender that’s really got some dried-out gunk stuck under the blades benefits from soaking in a mix of warm, soapy water and a tablespoon of white vinegar or even some kind of oxygen bleach (like OxiClean, the stuff you use in your laundry) for a few hours or overnight, depending on how bad the mess Apr 18, 2014.

How do you clean a blender with baking soda?

Simply put one cup of white vinegar, a few drops of dish soap and half a cup of baking soda into your blender. The mixture will bubble up, when the bubbling subsides, turn your blender on for a few seconds to mix everything together thoroughly and then let it sit in the jug for a few hours.

Is vinegar good for cleaning stove tops?

White vinegar is the ultimate cleanser. It is used to clean glass stovetops by loosening streaks and stains. Just mix one part white vinegar to two parts tap water in an unused spray bottle. Next, spray the solution on your glass cooktop and wipe.

Can you put raw carrot in a NutriBullet?

Yes you can use broccoli, carrots, kale and cauliflower. I have used them all and it broke it all down to a drinkable drink. I always add crushed ice to my drink.

What is the black stuff coming out of my NutriBullet?

It is common to notice a black stuff issuing forth from a nutribullet blender. This black substance is usually a mixture of the lubricants used to smoothen or oil its moving parts and the blended substance. In some cases, the black substance can be as a result of a leaking gasket, which is a tight seal on its blades.

How long does NutriBullet last?

Nutribullet blenders are guaranteed for 1 year of performance. However, your Nutribullet can last well over 5 years given appropriate use and care. Keep reading, and we’ll tell you how to properly handle your Nutribullet to keep it blending like new for years to come.

What is the black stuff coming out of my blender?

The black material coming out the bottom of the blender is a combination of lubricant & the material you blend. If you put the blender in the dishwasher, or soak it for a very long time, the lubrication is pushed out, causing excessive wear to the bearing in the blending assembly.