Quick Answer: How To Cover Electrical Panel In Living Room

Table of Contents

Strategically placed artwork, framed message boards, or a weaving or tapestry are all viable options for covering up obtrusive electrical eyesores. HGTV suggests inserting child proof safety plugs into unused outlets before covering with artwork.

Is it OK to cover electrical panel?

You are allowed to cover your electrical panel but it must be easy to open, can not interfere with the opening of the steel door of the panel and you have to make sure you have full access to all of the breakers. Keep in mind that some local electrical codes may prohibit the covering of your electrical panel.

How do I hide my fuse box in my living room?

Keep the unsightly out of sight! Use an old book cover to conceal your router. Or stash it away in a decorative box. A hinged painting will conveniently cover a fuse box or wall outlet. The same concept can be used to tidy up your entertainment center if you’re handy enough to cut a storage shelf into the wall.

How do I hide my breaker panel?

To cover a breaker box using a painting, follow these steps. Install the Hinges on Your Chosen Artwork. Install the hinges on the side of your painting with your screwdriver. Attach the Cover to the Wall Where Your Panel Box is Located. Install a Securing Lock. Photo Frame. Mirror Board. Note Board or Message Board. Pegboard.

What can I use to cover an electrical panel?

Can I build a closet around my electrical panel?

ANSWER: According to Section 240-24(d) of the National Electrical Code (NEC), which says “Overcurrent devices shall not be located in the vicinity of easily ignitable material, such as in clothes closets,” you are not permitted to do this.

How can I hide an electrical outlet?

Hang a picture over the outlet. For outlets positioned higher on the wall, screw a hook or nail into the wall above it. Hang the picture over the outlet for easy access in case you need to use it while effectively hiding it. Avoid taping posters over the outlet, as these can be harder to remove if you need to use it.

How much space do you need around an electrical panel?

The space around electrical equipment should always be clear to be on the safe side. There should be at least 3 feet of space in front of equipment with a 30 inch width as well as 612 feet of headroom space.

Can an electrical panel be on an interior wall?

Installation. Electrical panels mount in interior walls or hang on basement walls. However, they might require horizontal clearance, preventing them from being mounted in corners or other tight spaces. Installation provides a practical limit on where you can install an electrical panel.

Can you put an electrical panel in a laundry room?

According to the Meriwether Lewis Electric Cooperative, electrical panels must have an open space 30 inches wide and 36 inches deep for overall electrical and fire safety. These panels can be placed in a laundry room, as long as appliances and piping do not infiltrate the open space rule.

Can you cover up an electrical junction box?

Junction box covers must remain accessible; they cannot be covered with drywall or other surface material. A junction box is most often used where an electrical circuit branches off in two or more directions from a location where an outlet or fixture is not practical.

Can you hide a junction box in a wall?

A junction box, also known as a splice or switch box, is an electrical enclosure inside your home that contains wiring. It is a safety hazard to completely bury a junction box in a wall.

Can I Sheetrock over junction box?

Applying drywall over a junction box is never a good idea. According to the code, your junction boxes should always remain accessible, regardless of how good of a splice you made. So, the best option you have is to not cover junction boxes.

Can I put duct tape over an outlet?

One roll should cover every low-lying outlet in the house. You can also use duct tape if you want it to stick a little better; however, duct tape could leave a sticky residue on your outlets and walls.

Can I hang a picture over an outlet?

You can accomplish what you are asking with far less risk or hitting the electric line by using a wall anchor that is rated for slightly more than the weight of your planned picture. But, with caution, yes – you can hang the picture over the high receptacle and anchor it to the wall.

Is covering an outlet a fire hazard?

So long as the plug is completely pushed into the outlet and the two prongs are not exposed, then there is little danger of a cross over connection by something in the room space; however, it is always better not to have things stacked up tight against an electrical appliance or outlet to avoid potential of fire.

Does an electrical panel have to be on an outside wall?

3 Answers. They are almost always on an exterior wall. In some areas they are on the outside of the exterior wall – outside your house. Most inspectors would tell you that a garage (interior or exterior wall) or in the basement exterior (right where the line comes in) are the two best locations.

How far does an electrical panel have to be away from a window?

As far as the electrical equipment goes there is nothing beyond the working clearances. The equipment can be directly adjacent to either item. Working clearance for a panel is 30″ wide and 36″ deep (in front).

Can I put an electrical panel in a kitchen?

You cannot put it over anything. You cannot put it next to anything. There must a clear space in front of the panel for an electrician to stand. The space must be kept clear for at least 3 feet in front of the panel, and for 30 inches left to right in front of the panel.

Do electrical panel doors have to be closed?

4 Answers. National Electrical code does not require a door to cover breaker handles. It does require a cover that prevents access to electrified parts, which must have all openings closed. A panel without a door is not a violation, but a panel without a cover is.

Can a breaker panel be in a bathroom?

An electrical panel containing the service disconnecting means cannot be located in a bathroom [230.70(A)(2)]. In other than dwelling units and guest rooms in motels or hotels, panelboards containing overcurrent devices can be located in bathrooms.