Table of Contents
What do you use to cut a nut off?
A nut-splitter is a handy tool to remove nuts. It has a chisel inside its head that is screwed into the nut to pop it off.
How do you cut a nut in half?
Get a hacksaw blade and lay it on the marker line where you are going to cut. Run the drill while holding the hacksaw firmly on the bolt cut line. Keep holding pressure on the hacksaw blade until the bolt is cut in half. The two nuts will assist you to keep the blade steady.
How high should the nut be on an acoustic guitar?
Generally, the bottoms of the nut slots should be a few thousandths of an inch higher than the tops of the frets when the neck is straight. To check nut-slot height, hold the string down at the third fret, and see how much it moves over the first fret.
Does heating a bolt weaken it?
The answer is surprisingly simple: the bolt expands, but the nut expands more. What is happening here is good old thermal expansion: The bolt is heated and expands outwards, its radius increasing.
Does heating up a nut help loosen it?
Use a Bernzomatic torch and a little elbow grease to loosen frozen, rusted or stubborn nuts and bolts. For stubborn bolts, heat the bolt, then move the flame away and apply WD-40 against the heated bolt threads. The melting wax pulls itself into the threads to create a slippery surface.
Will a propane torch loosen bolts?
Some bolts just won’t budge. To remove a really stuck bolt, get some good penetrant—nothing works like PB Blaster—and a propane torch, available at any hardware or automotive stores. You can also use a butane torch, but it’s a little cheaper and easier to go with the propane.
How do you loosen a bolt left or right?
Shop-work. Typical nuts, screws, bolts, bottle caps, and jar lids are tightened (moved away from the observer) clockwise and loosened (moved towards the observer) counterclockwise in accordance with the right-hand rule.
How do you get a nut on a bolt with bad threads?
Use a rethreading tap to restore threads on nuts or threaded engine component holes. Don’t try to rethread the entire bolt, hole or nut in one operation. Insert the rethreading tap or die and rotate a few turns, then back it off a full turn. That will dislodge the debris from the teeth.
How do you remove a cross threaded nut?
Using a ratchet and socket, slowly work the bolt or nut back and forth. Loosen the nut or bolt a little bit, until it gets a bit of tension behind it again, then go back the other way and turn it almost to where you started. Then loosen it a little bit further than last time.
What can I use instead of a wrench?
What to Use if You Don’t Have a Wrench Duck tape. Duct tape is useful in almost any situation but you may be surprised to learn that you can use it to loosen bolts. Two coins. Who would think that money can be used as a makeshift tool? Zip-tie. Another nut and bolt.
Should the guitar nut be glued?
Is it necessary to glue a guitar nut in place? Gluing the nut is not completely necessary, the pressure of the strings and the friction between the nut and neck will hold it in place. However, you can use a few drops of white wood glue to fix it in place to prevent it falling off when changing strings.
Can a guitar nut cause buzz?
A poorly cut and set-up top nut can cause bad intonation, string buzz and affect the playability of the first few frets of your guitar.
Is it hard to change guitar nut?
Be very careful, because if you drop the nut too far down into the slot, the open strings will buzz against the first fret. Once you’re happy, place two small dabs of superglue on the underside of the nut and seat it in the slot. The key is to work slowly and accept that replacing a nut can be a long procedure.
How deep should guitar nut slots be?
The slots should be only deep enough so 1/3 of the string is above the top of the nut and 2/3 in the nut.
How high should strings be at the nut?
The top of the nut is shaped to follow the radius of the fretboard, and the string slots also follow this curve. To allow the strings to clear the top of the first fret, the bottoms of the slots should be . 030″ higher than the fret height.
Can nut slots be too wide?
The strings may still bear at the front edge, be supported along the entire slot, be at the right height and spaced evenly. If your nut has deep grooves that are too wide, and the whole thing looks messy, don’t fret.
What tool is used to cut bolts?
A bolt cutter, sometimes called bolt cropper, is a tool used for cutting bolts, chains, padlocks, rebar and wire mesh. It typically has long handles and short blades, with compound hinges to maximize leverage and cutting force.
Can you cut a bolt with a Sawzall?
Reciprocating saws fitted with the correct metal cutting blade make easy work of sawing through bolts, rods, rebar, pipes, profiles, and nails in stud work.
Can you cut bolts with a multi tool?
The plunge cut design is one of the most common types of metal cutting blades for an oscillating tool. For example, you might need to cut through a rusted bolt or cut a piece of pipe straight through. The plunge cut blades for an oscillating tool have the teeth arranged in a straight row.
Will a hacksaw cut through a bolt?
Cutting through the threaded part of a bolt, so that the nuts will still screw on and off easily, is really a very simple thing to accomplish. Now go ahead and, using either a hacksaw or bolt cutter, cut the bolt where you want. A hacksaw is preferable, especially for larger bolts.
