Table of Contents
What size hole do I drill for door latch?
The standard sized bore hole is 2 1/8″ in diameter. Through the edge of the door there is a 1″ cross bore that extends from the edge of the door through the bore hole. This cross bore is where the latch is installed. In addition to the two cross bores, a door can be prepped for one of 3 different types of latches.
How do you make a hole in a door without a drill?
Use two wooden sticks – tie a strong piece of string on both ends of one to serve as a bow, and the other should have a sharp end on one side and a handle on the other. Scrape out a small hole in the wood, where you wish to drill your hole. Place the pointy end of your second stick there and apply pressure.
What is standard door latch size?
We generally recommend that a 76mm Overall Latch Size is ordinarily the best size for most lever handles. However the shorter 64mm Overall Size should be used where the door is glazed, to minimize the risk of hitting the glass rebate when drilling to fit the latch.
What is the door latch hole called?
The latch bore, also known as the edge bore, is the hole drilled from the side of the door into the cross bore to allow the latch of the lock to be installed and to accommodate the sliding of the deadbolt. The diameter of the latch bore is generally 1” to accommodate bolts from either mechanical or electronic locksets.
What kind of saw do you use to cut a hole in a door?
A circular saw makes a great door cutter. Make sure your saw blade is sharp and has a minimum of 18 teeth. Hold the circular saw against the edge of the door as if you’re ready to cut. With the blade teeth held just to the waste side of the scored line, mark the masking tape along the opposite edge of the base plate.
What are spade bits?
Also commonly known as paddle bits, spade bits have a wide, flat blade. The flat, broad blade of a spade bit has a pilot point attached to a 1/4-inch diameter shank that can be chucked into both regularly-chucked drills and quick-chuck impact drivers.
What tool is used to make holes?
A hole may be drilled or bored; awls, gimlets, and augers also produce holes. An awl is the simplest hole maker, for, like a needle, it simply pushes material to one side without removing it. Drills, gimlets, and augers, however, have cutting edges that detach material to leave a hole.
Are all door latches the same?
In the United States, there are two common backsets for residential door locks: 2 3/8 inches and 2 3/4 inches. Pack your locks with a 2-3/8-inch or 2-3/4-inch latch, depending on which backset you specify.
What is a tubular latch for a door?
A tubular latch is an item of ironmongery which is usually morticed* into a door, which allows the door to be opened and closed by means of a Door Handle or Door Knob. Firstly, the Tubular Latch is without doubt, the most common type of door latch on the market today.
What is chisel tool?
chisel, cutting tool with a sharpened edge at the end of a metal blade, used—often by driving with a mallet or hammer—in dressing, shaping, or working a solid material such as wood, stone, or metal. Chisels today are made of steel, in various sizes and degrees of hardness, depending on use.
What is wood chisel?
A chisel is a tool with a characteristically shaped cutting edge (such that wood chisels have lent part of their name to a particular grind) of blade on its end, for carving or cutting a hard material such as wood, stone, or metal by hand, struck with a mallet, or mechanical power.
How do you cut hinges without a router?
To cut door hinges with a chisel place your hinge on top of the door to make an outline with a pencil. Using a chisel and hammer, make grooves along the traced outline and do the same on the outside to measure the depth. Using the hammer and chisel carve the outline to dig out the score from the door.
What is a lock verb?
lock verb (FASTEN) to fasten something with a key, or to be fastened with a key: If you shut the door it will lock automatically.
How do you cut a strike plate in door jamb?
Position the strike plate on the jamb so it is centered on both lines. Score around the plate with a sharp utility knife. Using a sharp 1-inch-wide chisel, cut a series of parallel lines into the jamb about 1/4 inch apart, staying within the scored lines and holding the chisel perpendicular to the wood.
What is the small part of a door latch for?
“Deadlocking plunger” (also called “deadlatch plunger” or “deadlock plunger”) is the name of a very important piece of a door lock assembly; it keeps a locked door from being opened with a small screwdriver or credit card.
What do you call the part of the door the lock goes into?
Cylinder (Lock Body) The cylinder, or lock body, is the part of the door lock where you insert the key. When it’s locked, the cylinder engages a series of spring-loaded pins which keep the cylinder from turning.
What are the parts of a door latch?
Parts of a Door Lock Knobs and Handles. The common door lock will have two knobs or handles—one on the inside of the door and one on the outside. Rosette. The rose or rosette is typically a round plate that serves two functions. Lock Cylinder. Spindle. Latch Assembly and Spring Bolt. Deadlocking Plunger. Strike Plate.
