Table of Contents
Why is my fluorescent light fixture not working?
If a fluorescent tube neither lights nor flickers when switched on, first check to see that the fixture is plugged in and that no fuse has blown or circuit breaker has tripped. If this does not help, try wiggling the tube gently in its sockets by rocking it back and forth and from side to side.
How can you tell if a fluorescent light ballast is bad?
If your fluorescent lighting is displaying any of the signs below, it could be a symptom of a bad ballast: Flickering. Buzzing. Delayed start. Low output. Inconsistent lighting levels. Switch to an electronic ballast, keep lamp. Switch to an electronic ballast, switch to a T8 fluorescent.
How can you tell if the ballast is bad?
One probe of the multimeter should touch the hot wire connections, while the other touches the neutral wire connections. If the ballast is good, an analog multimeter has a needle that will sweep to the right across the measuring scale. If the ballast is bad, then the needle won’t move.
How much does it cost to replace a ballast?
A replacement ballast costs about $10-25 depending on capacity and brand. The bite is that an electrician trip charge (which includes 30 or 60 minutes work) is going to be $75-150 probably – for about 5 minutes work on each light fixture.
How do you fix lights that won’t turn on?
Tighten the bulb if it is loose, then try the switch again. If a problem remains, be sure the switch is off, remove the bulb and substitute a new one. If the light does not work with a new bulb, check whether the circuit breaker or fuse governing the fixture has tripped or blown.
How long does a ballast last?
According to the Certified Ballast Manufacturers Association, the average magnetic ballast lasts about 75,000 hours, or 12 to 15 years with normal use. The optimum economic life of a fluorescent lighting system with magnetic ballasts is usually about 15 years.
Why are my fluorescent lights flickering?
If your fluorescent bulbs flicker, most likely the problem is with the bulb itself. If the bulb is very dark on either end, it may be defective and burned out. The best way to test the functionality of a bulb is to put it into a fixture you know works. Flickering fluorescent lights can also be a result of temperature.
How do I know if my ballast is T8 or T12?
If no markings are available, the size in diameter of the tube is the easiest way to determine the type you have installed. T8 tubes are 1-inch in diameter and T12 tubes are 1 1/2 -inch.
Does a bad ballast burn out bulbs?
The ballast itself can go bad, which causes lights to flicker or even appear to be burnt out, when in fact they aren’t. They require maintenance and energy to power, on top of the power used to light the fluorescent bulb. They are a large part of the equation when using fluorescent lamps.
Do I need an electrician to replace a ballast?
Yes. In fact, you really need a locking device to replace the ballast. – An electrician replaces the ballast on a fluorescent lamp. He uses a switch on the wall to turn off the fluorescent light.
Can you replace a ballast yourself?
The ballast takes in electricity and then regulates current to the bulbs. You can get a new ballast at a hardware store or home center and install it in about 10 minutes. However, buying a ballast can be expensive, so consider pricing a brand-new fixture for comparison.
How do you know if you need to replace a ballast?
2. Look for warning signs that the ballast is failing. Buzzing. If you hear a strange sound coming from your bulbs or light fixture, like a buzzing or humming noise, that’s often a sign your ballast is going. Dimming or flickering. No lights at all. Changing colors. Swollen casing. Burn marks. Water damage. Leaking oil.
Why are some lights in my house not working?
If one or more lights in your home have gone out and your circuit breaker isn’t tripped, what could the issue be? One culprit could be a GFCI (Ground Fault Circuit Interrupter) outlet that has tripped. Other issues can include loose wiring or outlets. Over the years, wiring and screws can come loose.
Why would a light switch suddenly stop working?
If the issue persists, it could be anything from a loose wire to a short circuit. A short circuit is caused when the hot wire (black wire) touches another hot wire or touches a white neutral wire. A break in a wire in the circuit can also cause this problem. Learn how to fix light switch breaker overloads.
How do you fix a flickering neon light?
If the sign illuminates but a tube FLICKERs: Pull the “on/off” pull-chain (on the power supply) … pull quickly on and off two or three times ending with it off …then wait for 1 minute. Turn it on again and the problem should go away within a few minutes (if this fix is going to work at all).
Where is the ballast on a fluorescent light fixture?
Locate the wiring cover plate, usually in the center of the fixture. On either side of the cover, there will be tabs that catch in slots in the fixture. Squeeze the sides of the cover inward to slip the tabs out of the slots, and pull the cover down. This will expose the ballast and its wiring.
