Table of Contents
Should there be a gap between toilet and wall?
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.
How do you move a toilet closer to the wall?
Install the Offset Flange Positions the offset flange so that the bent end moves the flange opening closer to the wall. Make sure the back of the offset flange connects snugly with the drainage pipe. Check to make sure that the flange’s opening is sitting flush and even against the bathroom floor.
How do you fill the gap between toilet cistern and wall?
If there is no way to move the pan back, then cut a couple of bits of white 32mm waste pipe to fit between the cistern and wall, one for each screw hole, and then screw the cistern back with longer screws. 25mm isn’t too bad and once the lid is on will look fine.
How do you fill the space behind a toilet?
Filling The Empty Space Behind The Toilet Hang towels. Install hooks for baskets. Mount an open shelf. Mount multiple shelves. Mount baskets. Mount a storage unit. Create built-in shelving. Add a storage tower.
How far away should the back of the toilet be from the wall?
The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing. Minimum distance in front of the toilet to the facing wall or fixture is 21 inches.
How far from the back wall should the toilet flange be?
The Distance To Set The Toilet Flange From The Back Wall. You’ll want to set the center of the water closet flange 12 inches from the finished back wall.
Is it difficult to relocate a toilet?
Moving a toilet is not so much about moving the actual fixture—in fact, installing a toilet is a simple job that takes less than an hour—as it is about moving the drainage and the water supply plumbing to the new location. Once all of the plumbing is in place, installing the toilet is a relatively easy task.
How much does it cost to relocate a toilet?
The cost to move a toilet or sinks can be $2,500-$3,500 per fixture. Plumbing can be a significant cost factor in a remodel when a bathroom floor plan is altered. The toilet is the most expensive to move. Connecting the toilet to the existing sewer line can be a bit tricky for your plumber.
How far from the wall should a toilet waste pipe be?
1 Answer from a MyBuilder Plumber Close coupled toilets/ back to wall toilet pans/ or vanity unit toilets. All of which have different distances but the height will always be the same which is 7 inch from finished floor tho center of toilet outlet.
How far is toilet rough-in from wall?
The general rule of thumb for clearance from the wall that faces the bowl is 24″ and just about 15″ on each side. The rough-in measurement indicates how much clearance you have and will allow you to select a compatible toilet.
How far should toilet flange be above finished floor?
Check the Flange Height With the toilet removed, you can see the toilet flange and measure its height above the floor. The optimum flange height to aim for is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal.
How do I know if my toilet is a 10 or 12 rough?
If the old toilet is still there, measure from the center of the capped bolts (on the bottom) to the wall (not the baseboard). There should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side as a guideline. If your measurements are between 11.5 and 12.5 inches, it is a 12-inch rough-in.
What does 12 rough-in mean for toilet?
The toilet rough-in refers to the distance from the finished wall to the center of the toilet’s floor drain or waste outlet. Most toilets have a rough-in of 12 inches, although it’s not uncommon for older homes to have an unusual size such as 10″ or 14″. Rear-outlet toilets are configured a bit differently.
Can you put a toilet anywhere in your house?
On a serious note, it is absolutely possible to install a toilet, even a bathroom as a matter of fact, anywhere in your house. In the past, many homeowners have had the idea of their dream bathroom crushed because the location was simply too far away from the main drain.
Can you switch a toilet and shower?
The simple answer is yes, you can put a toilet where a shower was, but the move doesn’t come without its issues. This isn’t a simple DIY job. You are going to have to remove at least one wall and, hopefully, only a small portion of the floor.
