Table of Contents
For those with gas chainsaws, put your right foot through the back handle and put your weight down on the handle to secure the saw. Use your left hand to hold the front handle firmly in place. With your right hand, pull the starter rope out sharply to its full length.
What is the proper way to hold a chainsaw?
How do you use a chainsaw for beginners?
If you’re starting the saw between your legs, place the back handle between your thighs and hold the front handle firmly with your left hand. Pull the starter handle with your right hand until the engine fires. Push the choke and pull until the saw starts. Release the chain brake.
How hard is it to use a chainsaw?
Chainsaws are relatively easy to use once you get used to them but they are dangerous. They will cut flesh and bone as if it is not there.
What should you not do with a chainsaw?
Don’t Cut With a Dull Blade Cutting with a sharp blade actually extends the life of your chain saw. That’s because a sharp blade pulls itself into the wood, while a dull blade requires lots of downward pressure. That pressure wears out the bar, drive links, clutch sprocket and clutch.
Should you run a chainsaw at full throttle?
Engine Protection Generally, two-stroke chainsaw engines are built to conveniently run at full throttle without an engine breakdown. Therefore, running at any throttle speed below the full throttle is not advised.
What is the most common chainsaw injury?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
How do I stop my chainsaw kickback?
Ways you can avoid chainsaw kickback Read the manual. Make sure the chain brake works before you start. Use low-kickback chains. Use a sharp chain. Be wary when felling tree trunks. Pay attention to the nose of your chainsaw bar.
How tight should a chainsaw chain be?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
How does chainsaw kickback happen?
There are two circumstances that can cause kickback when using a chain saw. The first occurs when the moving chain at the tip or the nose of the guide bar strikes an object. The second situation is when the wood closes in, pinching the saw chain in the middle of the cut.
How often should you change the bar on a chainsaw?
If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw once after you have gone through three chains on the same bar.
Should you wear gloves with chainsaw?
Always wear protective gloves when using a chainsaw. Chainsaw gloves are just one component of what you should wear when cutting wood. The other essentials are: Chainsaw chaps, protective head gear and a cut-resistant jacket.
Can you cut a hedge with a chainsaw?
A chainsaw can be used to trim bushes, hedges and shrubs. While not as effective as a hedge trimmer, a chainsaw can cut fast enough to trim through lighter woods. If it’s only needed to pair back overgrown bushes, a chainsaw will suffice.
Do you need to break in a chainsaw?
Does my chain saw have a “break in period”? Typically we recommend a break in period of 6-10 tanks of fuel. Also recommend after you have used 6-10 tanks of fuel you take the unit into your local authorized servicing dealer to have the carburetor readjusted for optimum performance.
How long should you run a chainsaw?
Upon first starting a chainsaw, you need to let it idle for at least 30 seconds, but longer is better.
How long can a chainsaw run?
What is the runtime of a Chainsaw? Depending on the type and usage, you can expect a gas Chainsaw to run between 15 and 40 min before you have to fill it up again. Most battery-powered chainsaws have a run time of up to 2 hours, but there are high-capacity power packs that will last much longer.
How do you not pinch a chainsaw?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
Can anybody use a chainsaw?
Chainsaws are potentially dangerous machines which can cause fatal or major injuries if not used correctly. It is essential that anyone who uses a chainsaw at work should have received adequate training and be competent in using a chainsaw for the type of work that they are required to do.
How many people are injured by chainsaws every year?
According to the Centers for Disease Control and Prevention (CDC), approximately 36,000 people are injured by chainsaws annually. Medical costs for chainsaw injuries based on these facts amount to about 350 million dollars per year.
What is a chainsaw kick guard?
Prevents chainsaw kickback A tip guard helps to prevent accidental dulling of the chain by keeping the nose clear of abrasive objects, in addition to protecting the nose from accidental contact with the ground or other obstructions.
