Table of Contents
How much does it cost to install a Tommy lift gate?
To put a liftgate on your truck, you’ll need to consider your application among other specifications. Depending on the lifting capacity, power supply, and choice of material, the cost price will range between $2,000 to $9,000.
How long does it take to install a lift gate?
Most lift gates can be fully installed within two to four days after the order is placed.
How much weight does a lift gate add to a truck?
Again this depends on the type of lift gate the carrier has attached to their truck. Lift gate weight capacity can range from 1500 lbs to 3500 lbs.
How much does a Tommy Lift cost?
There are myriad specs to consider, with cost ranging from $2,000-$9,000, depending on the type of gate, platform size and material, power supply, and lifting capacity.
What is a tuck under lift gate?
TuckUnder™ liftgates mount to the chassis frame of a truck or trailer and store folded to provide full access to the vehicle doorway. Standard ramping ride models start level at the truck or trailer floor and gradually tilt to ground level.
How much does a Tommy Gate weigh?
1300 & 1500 lbs. Original Series The Original Series is a single-cylinder, parallel-arm design based on a cable and pulley system. The classic pickup lift.
What kind of fluid does a Tommy Gate use?
Lubricate the roller chains, sliders, uprights, and pivot points with clean, high-quality, nondetergent, petroleum-based oil – DO NOT USE GREASE. Use nondetergent 10W @ (14°F-32°F), 20W @ (32°F-104°F), and 30W @ (104°F-122°F).
Why is my Tommy Gate not working?
The most common liftgate issues can be traced back to the motor or motor start solenoid. Using a small jumper cable, bypass the solenoid by putting direct power to the motor to see if it will run. If it doesn’t, safely check and replace any broken fuses or reset breakers.
How do you remove a Tommy Gate?
Proceed to the passenger’s side of the Tommy Gate and remove the latch padlock. Push the passenger’s side latch to the side, off the platform pin with one hand while holding the top of the platform with your other hand. Pull the platform open and step away from the platform as it opens.
How much do Liftgates cost?
Depending on the lift gate model and size, a unit can cost anywhere between $2,000 to $7,000. Lift gates can handle up to around 3,500 pounds (about 1.6 tons) and fold up after use.
How do you manually lower a Tommy Gate?
To activate the control, press the “LIFTGATE ACTIVATED” hidden switch twice within one second (located under the Tommy Gate logo). You should see the red “LIFTGATE ACTIVATED” light when the control is activated. To lower the platform, push the toggle switch down. To raise the platform, push the toggle switch up.
How much does a Tommy lift gate weigh?
What is this? With a lifting capacity of 650, the Tommy Gate 650 Series weighs 355 lbs. As a low-capacity, compact, and internally-mounted liftgate, the 650 Series is the ideal liftgate for lightweight van applications.
How much does a Maxon liftgate weight?
MAXON’s new TE-33 liftgate model has taken “standard” to a whole new level. The 3,300 lb, medium-duty, Tuk-A-Way® delivers premium features in a standard tuk.
How much weight can a lift gate hold?
Most liftgates can handle freight that is equal to or less than 96 inches wide, and 48 inches deep. This means that standard-sized pallets can easily be used with a liftgate. The weight limit on a standard liftgate is 2500 lbs.
How long do Liftgates last?
“They’re very handy, and they last a long time — at least 10 years — and they run off the truck batteries with no charging assistance.” Another fleet executive said liftgates can improve operations.
Can you tow with a lift gate?
Your customer never has to install or move the hitch, and absolutely no load stresses are placed on liftgate models during towing. (Available without trailer hitch.
Who invented the Tommy lift?
Woodbine Manufacturing Company was founded in 1965, in Woodbine, Iowa by Delbert “Bus” Brown. Working alone, Bus designed and constructed the original Tommy Gate Hydraulic Lift, which he named after his son.
How do you adjust Tommy liftgate?
To activate the control, press the “LIFTGATE ACTIVATED” hidden switch twice within one second (located under the Tommy Gate logo). You should see the red “LIFTGATE ACTIVATED” light when the control is activated. To lower the platform, push the control toggle switch down.
What is a Tommy Gate on a truck?
Pickup liftgates are used to lift all kinds of heavy cargo from oil drums to common household appliances. Knowing what the liftgate will be lifting is essential to identifying what lifting capacity, platform loading size, and platform material will be ideal for the application.
What is a rail gate on a box truck?
Rail Gate. Rail liftgates are best used for loading and unloading bulky and heavy items because of their large and level platform. Compared to a tuck under, rail liftgates have more loading space. When engaged, the lift deck is folded down and travels straight up and down.
What is the difference between a rail gate and a lift gate?
Railgate. A conventional liftgate doesn’t provide as much space or capacity as a railgate, but it makes dock loading much easier. A conventional liftgate might also be more efficient when it comes to smaller loads; however, it could be too small for larger loads.
What is the difference between tailgate and liftgate?
The Difference Between A Liftgate And A Tailgate You lift a liftgate upwards, while you lower a tailgate. A tailgate is lowered for loading or unloading.
Why wont my liftgate go up?
Your Lift gate won’t lift off the ground Lift gates are run by a motor/pump and when they malfunction, it could be due to issues involving the motor/pump itself. Your lift gate may have a problem with a defective switch or a broken wiring connection.
