Table of Contents
How much should LP SmartSide overlap?
Overlap successive courses of siding a minimum of 1”. Siding shall be installed with top (blind) nail placed 3/8” from each end, and 3/4 in. down from the top edge of the board. Siding shall be face nailed 8 in.
Do you need sheathing under LP SmartSide?
LP SmartSide lap and panel siding is designed to be installed in a direct to stud application, but also offers the flexibility of being installed in a sheathing only method.
How long does it take to install LP smart siding?
Therefore, you can expect installation to take an average of 10 to 12 days. If the siding needs painting, expect the job to last an additional five days.
Can you screw LP SmartSide?
Nail & Screw Requirements LP SmartSide has three product categories: Precision Series, Foundations and Architectural Collection. When installing Precision Series lap in this application, you may use 0.091″ diameter, hot-dipped galvanized ring shank nails or #8 hot-dipped galvanized tapered head wood screws.
Does LP SmartSide need to be nailed into studs?
When strips are required, they must be installed VERTICALLY and nailed into wall studs, 16 in (405 mm) O.C., over the full height of the wall.
Do you need plywood behind LP siding?
a. No. LP SmartSide vertical siding can NOT be attached directly to studs, it must be attached to a minimum 7/16 category wood structural panel wall sheathing.
Is lap siding structural?
APA Rated Siding panels and lap siding are structural products produced with known and reliable strength and stiffness properties. Siding panels can be applied direct to studs or over sheathing.
What is LP OSB?
LP OSB (Oriented Strand Board) Sheathing. OSB. MPN: P-LPOSB P-LPOSB. A cost-effective, high performance structural panel, LP® OSB is designed for optimal performance and stability. It contains only low-emitting safe resins and is offered in a comprehensive range of performance categories.
How long does LP smart siding last?
Frankly, while the LP SmartSide warranty lasts 20 years beyond Hardie’s, it is prorated, so it loses value every year, and most homeowners are ready for a siding change by that time anyway.
How long does it take to install lap siding?
Every house is different, but a typical tear-off and siding installation project may take between 7 to 14 days. There are many things that can extend the time such as the size of your house, whether you’re using prefinished siding or if it needs to be painted, and unexpected repairs.
Can you Miter LP siding?
Can LP® SmartSide® trim and fascia be miter cut? Do not miter cut the edges or ends of the trim at corners. Miter cuts or “picture framing” around door and window openings are acceptable.
Can you use screws on lap siding?
HardiePlank® lap siding may be used with fasteners approved by ICC-ES ESR-2290 spaced in accordance with the Wind Load Tables. Fasteners must be corrosion resistant, galvanized or stainless steel. Fasteners shall be installed between 1 in. and 3/4 in.
What is the difference between SmartSide 38 and 76?
What’s the difference between Series 38 and Series 76 Lap Siding? Other than material thickness, one main difference is 38 Series Lap Siding may be installed on studs spaced a maximum of 16 inches o.c. whereas 76 Series Lap Siding may be installed on studs a maximum of 24 inches o.c.
Can you hang siding with screws?
Fastener Choices Use aluminum, galvanized steel, or other corrosion-resistant nails, staples, or screws when installing vinyl siding. All fasteners must be able to penetrate a minimum of 1 1/4” (32mm) into nailable material, such as wood sheathing and framing (Fig. 15).
How do you measure for lap siding?
When matching vinyl siding, one needs to measure from the bottom of the panel to the first “lap”. This measurement will typically be 4, 4.5 or 5 inches. There are 2 laps, giving the appearance of 2 boards per each individual panel.
What is the overlap on vinyl siding?
There is a fine line between nailing too loosely and too tightly. Too Much Joint Overlap: The industry standard for overlap for vinyl siding is 1” to 1 ¼”.
Can LP SmartSide panels be installed horizontally?
LP SmartSide siding is designed for horizontal installation only. Un- grooved LP SmartSide Precision series panel siding is available for board and batten applications. Refer to the installation instructions for proper installation.
Should lap siding be caulked?
Bottom of siding boards should not be caulked While paint does tend to somewhat glue these pieces together, caulking them is never advised and can cause permanent damage.
Do you caulk butt joints on LP siding?
LP requires a minimum 3/16” spacing at all butt joints. Do I have to caulk at butt joints? It depends on the option you choose, but if joint caulking option is selected, seal all gaps at butt joints with a high-quality exterior sealant meeting the ASTM C920, minimum Class 25 sealant.
Can I use roofing nails for LP siding?
Can I Use Roofing Nails for Siding? Roofing nails, while they may be galvanized, are generally shorter in length and will not allow for the required 1-1/2 inch penetration into structural framing or wood structural panels and wood structural framing. Stick to nails designed for installing lap siding for best results.
Is LP smart siding OSB?
LP OSB Sheathing. Among the world’s most popular OSB sheathing products, offered in a variety of panel sizes and performance categories. All are APA-rated and backed by a 20-year transferable limited warranty.
