Table of Contents
How far does an offset flange move a toilet?
There is usually a vertical waste water pipe under the toilet that uses gravity to move wastewater away. For the waste water line, an offset toilet flange will allow you to move the toilet a couple of inches in any direction without having to cut a new hole in the floor or reconstruct the waste water pipe.
How do offset toilet flanges work?
Unlike a standard flange, which is centered on the waste pipe, an offset flange is off-center—that lets you shift the location of the toilet by a couple of inches (left, right, forward or back). P.S. Flanges with stainless steel rings cost a few bucks more than all-plastic versions.
Should toilet flange be flush with floor?
For those that don’t already know, the proper toilet flange height is when it’s flush with the top of the finished floor. Third, you can take off the flange as well as the toilet and trim down the waste pipe that comes up through your bathroom floor. This opening of this pipe should be level and flush with the floor.
Can a toilet be moved 6 inches?
Yes, you can actually move a toilet. Even moving a toilet by a few inches without having to make a new hole in the floor is possible. You can use an offset toilet flange to move the toilet by a couple of inches on any side.
How far does the toilet flange need to be from the wall?
The Distance To Set The Toilet Flange From The Back Wall. You’ll want to set the center of the water closet flange 12 inches from the finished back wall. Don’t measure from the base molding! Take this measurement from the finished wall.
What is standard toilet offset?
Standard drywall is 1/2 inch thick, so the plumber should set the toilet flange at least 15-1/2 inches from the center of the flange to the wall framing. The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing.
How do you move a toilet flange to the wall?
Install the Offset Flange Positions the offset flange so that the bent end moves the flange opening closer to the wall. Make sure the back of the offset flange connects snugly with the drainage pipe. Check to make sure that the flange’s opening is sitting flush and even against the bathroom floor.
How far should toilet flange sit above floor?
Check the Flange Height With the toilet removed, you can see the toilet flange and measure its height above the floor. The optimum flange height to aim for is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal.
Does toilet flange go on top of tile or flush?
The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too. The spacing of the toilet exit “horn” and sealing surface is designed for this height.
Does toilet flange go inside pipe?
Buy an inside closet flange. This toilet flange is designed to glue on the inside of the pipe or expand inside the pipe. The flange should be sitting with the bottom edge flush with the top of the floor. If it isn’t, then you will have to cut away the old flange.
Does a toilet flange need to be screwed down?
Yes, you have to screw or bolt the toilet flange to the floor. A bad seal between the toilet and the flange or the flange and the pipe can cause leakage, which will damage the bolts that hold the flange to the pipe or allow horrible smells to seep into your bathroom.
Is it difficult to relocate a toilet?
Moving a toilet is not so much about moving the actual fixture—in fact, installing a toilet is a simple job that takes less than an hour—as it is about moving the drainage and the water supply plumbing to the new location. Once all of the plumbing is in place, installing the toilet is a relatively easy task.
How far can a toilet be from the main stack?
Tie the waste line from the new toilet directly into the stack if the toilet is within six feet of the stack and the waste line is 3 inches in diameter. If the waste line is 4 inches in diameter, the toilet can be as far as 10 feet from the stack.
How much space do you need on either side of a toilet?
Toilets and Bidets Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture.
How do I know if my toilet is a 10 or 12 rough?
If the old toilet is still there, measure from the center of the capped bolts (on the bottom) to the wall (not the baseboard). There should be 24 inches of clearance from the wall facing the bowl and 15 inches on each side as a guideline. If your measurements are between 11.5 and 12.5 inches, it is a 12-inch rough-in.
