Table of Contents
Should I nail or screw roof sheathing?
Now, however, experts almost universally recommend using 8D common nails. “Your roof will be more resistant to heavy winds if you use the right nails to secure the sheathing,” according to James Bedford of Fort Collins Roofing in Fort Collins, Colo.
What thickness plywood should I use for shed roof?
Most builders use 15/32 CDX for the roof; it is an exterior-grade plywood with a thickness just under 1/2 inch. The floor needs to be more solid than the roof to support lawn maintenance equipment and people. Use sturdy, 3/4-inch-thick exterior plywood for the floor.
How far should roof sheathing overhang fascia?
Ideally the sheathing should be on top of the fascia without extending beyond it. Guesswork can create a situation in which it extends too far and it interferes with flashing installation, or you have to cut it. If the fascia is to be one layer of 1x, I overhang the sheathing 5/8.
Do you glue down roof sheathing?
Unlike flooring, DO NOT glue roof sheathing. Drive nails flush to the panel. Avoid over- driving nails through the panel surface, es- pecially when using a power-driven tool.
Can I use a framing nailer for sheathing?
The answer is, yes. Framing nail guns can be used for siding installation, if the nail being used is long enough to attach the siding firmly to your exterior wood sheathing. While it’s recommended to always use a siding nail gun for siding installation, in a pinch, you may be able to use a framing nailer instead.
Which is better for roofing OSB or plywood?
Plywood Holds the Moisture Advantage Over OSB When plywood gets wet, it tends to swell. OSB takes longer than plywood to get saturated, but also takes much longer to dry out. When used as roof sheathing, this tendency to hold moisture means it will degrade faster than plywood when exposed to chronic leaks.
Can I use 1/2 inch plywood for shed roof?
If the shed is for light tools then 1/2 inch pressure treated plywood is acceptable. If the shed is for heavier storage, then pressure treated 3/4 inch exterior-grade CDX plywood is the best.
How thick should roof OSB be?
Standard roof sheathing thickness is ½” to ⅝” thick. If you are using OSB for your roof deck, then ⅝” is the recommended thickness. For plywood, which is slightly stronger than strand board, ½” thick is appropriate. Another factor is how far apart your trusses or rafters are spaced.
Do you overhang roof sheathing?
Measure up the rafter 45-3/4 inch from the cut end of the truss tail and snap a line along the trusses. This indicates the upper edge of the first row of roof sheathing—leaving enough overhang that the subfascia and fascia will tuck neatly underneath when the time comes.
Can I use screws for roof sheathing?
Screws can be used for even greater withdrawal strength, but should be sized by the building designer. Staples are not recommended for roof sheathing attachment in high-wind areas. It is extremely important to have proper fastener spacing on all panels.
What goes on first roof or fascia?
Fascia and soffit are installed after the roof installation is finished. It is ideal that soffit and fascia materials be installed before you place tiles or any other type of roofing material on the roof.
How far should shingles extend over drip edge?
Shingles should not extend more than 3/4” (19 mm) past the drip edge. If shingles overhang the edge of the roof by more than 3/4” (19 mm), then they are not supported and may crack and break off. In addition, the wind resistance at the roof edge may be compromised.
What is the nailing schedule for roof sheathing?
As such, the nailing schedule is typically the familiar 6 inches on center at supported panel edges, including gable-end walls and 12 inches on center over intermediate panel sup- ports. Note, however, that minimum 8d nails (0.131 x 2-1/2 inches) are recom- mended for all panels 5/8 inch thick or less.
What kind of nails do you use for roof sheathing?
Using proper nails to attach sheathing will help your roof withstand strong winds. Traditional sheathing material typically comprises 15/32-inch plywood or oriented-strand-board (OSB) panels. Builders generally use 8d common nails, which are approximately 2 ½ inches long and 131/1000 inch wide in diameter.
Are roof sheathing clips required?
For the most common roof sheathing in our area, which is 1/2” nominal (7/16” actual) sheathing over trusses or rafters at 24” on center, there is no requirement for H-clips. One or two H-clips will often allow a longer span between roof trusses/rafters.
Do you have to stagger roof sheathing?
Staggering panels by at least two supports is recommended. During the installation of OSB, the rough surface side should be facing up. This rough side is a screened or skid-resistant coated side. The panels should be spaced 1/8-inch apart at the ends and edges.
Should I nail or screw OSB?
Nails are often preferred for structural joining, including framing walls, because they are more flexible under pressure, whereas screws can snap. Nails are also called upon when securing plywood sheathing for exterior walls, installing hardwood floors, and attaching siding and roofing.
Can a roofing nailer be used for sheathing?
1 Answer. Roofing nails are a bad choice for attaching sheathing. The wire gauge is too small and the hardness of the nail shank is much less than a framing nail.
Can a roofing nailer be used for framing?
Large-body nailers typically include framing nailers and roofing nailers. These nailers are used for more technical projects such as framing out a basement or installing roofing shingles. If you’re constructing a fence, a framing nailer is a good option.
