Table of Contents
What is SwiftLock laminate?
SwiftLock is a brand of laminate flooring made by Armstrong. Unlike solid wood flooring, engineered laminates are floating floors — the planks connect to each other but are not nailed to the subfloor. SwiftLock, and some other brands of laminates, have interlocking tongues and grooves milled into mating edges.
What is the proper way to install laminate flooring?
Follow these steps to install new laminate floors in your home: Step 1: Acclimate Your Planks and Prep the Subfloor. Step 2: Trim Door Jambs. Step 3: Install Underlayment. Step 4: Lay Your First Row of Laminate. Step 5: Continue Laying Planks. Step 6: Add Finishing Touches.
Where do you start when laying laminate flooring?
Always start hardwood flooring along the most prominent and noticeable wall in the room. This way, if the room is out of square, the crooked cut will be hidden under the cabinet’s toe kick. In order to keep the floor straight and square, start laying the laminate away from the wall because the wall may not be straight.
Why won’t my laminate floor stay together?
Some common reasons why laminate pieces won’t snap into each other include: A warped or flawed piece of laminate. A heaved or uneven subfloor. A piece of debris trapped under the flooring or underlayment, or in the flooring’s grooves.
Do you cut the tongue off the first row of laminate?
Place the first plank with the tongue side towards the wall, being sure to allow 1/8″ for expansion. We recommend cutting off the tongue on this first row to avoid any problem with the expansion gap. If it is too short, cut a new plank in half and use one half to start the second row.
How do you stop laminate flooring at doorways?
How To End Flooring at a Doorway Lift to Fit. Plan on a seam in the middle of the doorway. Notch and cut the first piece to fit and then slide it completely under the jamb. Slide Both Pieces Over. Once the two pieces are connected, slide them both over just far enough so that both jambs cover the flooring ends. 11 / 12.
What goes underneath laminate flooring?
What Is Laminate Underlayment? Laminate underlayment is a soft pad that is installed under laminate flooring. The underlayment helps the laminate planks lay smoother, connect better, and for the flooring to feel slightly softer underfoot.
Do you glue laminate flooring?
Laminate flooring is not recommended to be glued down. Since it is a floating floor, it is meant to support itself via locking systems and have no connection to the subfloor.
Does the tongue or groove go against the wall?
Which to Install First. Which side is the tongue, which the groove, and which goes first during installation? The tongue is the side that you will want to place against the wall as you start your laminate-flooring installation.
How soon can you walk on laminate flooring?
wait for the floor to cure Before you use your new floor or move into the room, make sure the floor is completely cured. Do not walk on the floor for 24 hours after installation. If you do, it will damage the installation, resulting in an uneven floor.
How do I make sure my first row of floor is straight?
Snap a chalk line down the middle, measure from that line to within a few inches of the starting wall, and snap a second line parallel to the first. Align your first piece with the second line. Then every couple of rows, measure to make sure you are still parallel with the first chalk line.
How do I keep my laminate floor from moving after I install it?
If your laminate floor is moving and shifting, you can fix it by closing any gaps between the floorboards. Ensure that the subfloor is even during installation, and there is no moisture retention in the floor area. Using wood glue to make sure that the floorboards do not fall apart is recommended.
Do you nail laminate flooring?
Since laminate flooring is a floating floor, it is not meant to be attached to the subfloor by nails or glue. The floor needs to be able to expand and contract with temperature changes and therefore must freely lay on the underlayment or subfloor.
How do you keep laminate floors from separating?
To prevent your floorboards from separating again just a few months after fixing the same problem, we recommend using high-end wood and laminate adhesives such as Gorilla Glue, Epoxy Glue, and Titebond III.
Do you need transition strips between rooms laminate flooring?
When transitioning from laminate to another type of flooring, an important issue is the difference in thickness between them. Laminate flooring is thinner than most other flooring types, so you usually need a transition strip called a reducer to avoid leaving a toe-catching edge.
Do you need transition strips between rooms laminate?
If you are dealing with two different types of floor coverings, a transition strip is almost always required. For laminate flooring, for example, you can purchase hardwood transition strips that look just like your laminate.
Are transition strips necessary?
Transition strips are especially important when you are going from one thickness of floor covering to another. It’s common to have an area that has thick carpet that transitions to concrete or carpet that transitions to another hard surface like wood, laminate or linoleum.
How do you start the first row of laminate floor if the wall is not straight?
How to Start the First Row on Laminate Floor if the Wall is Not Straight Step 1: Mark the Expansion Gap. Step 2: Determine Out-of-Square Measurement. Step 3: Begin at the Starting Wall. Step 4: Mark Half of Out-of-Square Measurement. Step 5: Angle and Intersect Chalk Lines. Step 6: Cut Boards at Markings.
Which way should you lay laminate flooring in Long room?
In general, laminate manufacturers recommend laying laminate flooring perpendicular to the longest wall in a long, narrow room to avoid a bowling alley effect. When the boards are laid across the room, the lines between the boards and the wood pattern visually widen the room.
Can you lay laminate flooring right to left?
We recommend starting in the left corner of the longest wall in the room and to install the planks in the same direction as the main light source (e.g. the main window). Planks are always installed from left to right.
