How To Install Vinyl Quarter Round

Table of Contents

Use the nailer or hammer and nails to attach the molding to the baseboard. Be sure you hold the quarter round tight against both the baseboard and floor for a tight fit. To hand-nail molding, drive each nail almost flush with the quarter round, then use the nail set to sink the head beneath the surface.

Should you glue or nail quarter round?

A: Quarter-round should be nailed to the base boards only. It is intended to hide gaps between the base and floor. It should also permit a little movement in the flooring. Plus, it absorbs the impact of feet and furniture legs, so you may want to replace it sometime—thus, don’t glue it.

What is the best way to attach quarter round molding?

Position each piece of trim and fasten it with a brad nailer or by hand-nailing with a hammer and nail set. The preferred tool for nailing shoe molding or quarter-round is an electric finish or brad nailer. This tool will automatically set or recess small finish nails, and can greatly speed up your work.

How do you install PVC quarter round without a nail gun?

Procedure: Step 1: Sweep dirt and debris. Sweep all the corners of your wall (and also along the edges and where else essential) clean. Step 2: Lay the quarter round flush against the baseboard. Step 3: Nail it! Step 4: Continue nailing. Step 5: Install more counter-rounds.

Do you need quarter round with vinyl?

No you never need to use quarterround. I try to do all installs without using it.

Can you glue quarter round trim?

Quarter-round molding is a thin strip of wood shaped with two flat sides and a rounded crest. Usually nailed to the baseboard, it is possible to glue the quarter round to the wood to avoid nailing, filling the holes and painting over the repaired surface to hide the evidence of mounting.

How do you secure quarter round to baseboard?

What size nails do you use for quarter round?

Attaching Quarter Round Because it’s finish trim, install quarter round with finish nails, which have smaller heads than standard nails. A finish nail gun, fitted with 1.5- or 2-inch finish nails, works well.

How do you join two pieces of quarter round?

Quarter round will always be cut at an angle, usually 45 degrees. Cut 2 joint pieces at 45-degree angles in the same direction (meaning both angled to the left, or both to the right). These joint pieces should fit together to form a flat line against the wall. Most corners will be 90-degree angles.

Do you nail or glue PVC trim?

To fasten the trim to the wall, I use 2 1/4-inch-long 15-gauge nails. On the interior of a home, nail holes in PVC can be filled with almost anything used with wood; Bond-and-Fill is a safe choice. To glue joints together, use PVC cement, since wood glues like Titebond II don’t work all that well with PVC.

Can I nail PVC Moulding?

Fasten PVC trim with stainless steel screws or hot-dipped siding nails. Stainless steel screws with small finish heads are the best choice because they’ll never corrode. You can also use hot-dipped galvanized nails, but they may corrode and stain the trim over time.

Is it necessary to install quarter round?

One of the most common questions people ask is if they really need the base shoe, or if it’s just an add on. The answer is a simple yes. Without it, there is typically a gap between the trim and flooring, which is not only unattractive but makes it extremely easy for dirt and debris to build up under the base trim.

Do you have to put quarter round on baseboards?

If you’ve been looking at baseboard finishing trim, you’ve probably discovered quarter-round, too. While quarter-round can be installed along the bottom of baseboard, trim carpenters and homeowners tend to prefer the sleeker look of shoe molding, which is taller and narrower than its curved counterpart.

Should I use quarter round when installing laminate flooring?

Never allow nails or screws in the Wallbase or Quarter Round to enter into the laminate flooring or the expansion zone around the flooring perimeter, as it will prevent proper expansion and contraction of the flooring.

Can shoe molding be glued?

Generally, don’t glue anything that may need to be serviced, unless you’re willing to risk having to destroy it to remove it. You can also pre drill a pilot hole Use a drill bit a tiny bit smaller then the nails. You won’t have a problem bending nails this way.

Can you glue trim to walls?

Apply Loctite Power Grab Molding & Paneling Adhesive to the back of the molding, keeping at least 1/2″ from the edge. Place the trimmed end of the crown molding on the wall next to the corner. The adhesive will keep the molding or trim in place while you tack it in place.

Can you use Liquid Nails for shoe molding?

On a clean work area, lay down the shoe molding face down and apply a bead of liquid nails in a zig-zag pattern so it covers the length of the molding. Put the molding up to the wall with the adhesive side facing the wall and press firmly into place. Carefully make sure everything is lined up.

Can you use 18 gauge nails for baseboards?

Yes, you can use an 18-gauge Brad Nailer for your baseboards. However, it doesn’t have the holding power compared to a 15 or 16-gauge nail. The 18GA nails work well for trims up to 1/2 inch. For baseboards thicker than 1/2 inch I recommend you go for 16 gauge nail gun.

What size nails should I use for baseboards?

As we discussed earlier with nail guns – the best baseboard nails are probably going to be 6d (2”) or 8d (2.5” for baseboard). These can easily accommodate 15 gauge or 16 gauge nails, giving you a long, durable nail for thick baseboards and studs.

What size brad nails should I use?

Having the right length of brad is crucial for a good result. The rule is simple: a brad should be three times as long as the thickness of the material you are fixing. Example: if the material is 15 mm thick, the brad should be 45 mm long. Choose a brad gun that takes the length of brad you need.