Quick Answer: How To Install Water Supply Line For Ice Maker

How do you install a refrigerator water line?

Instructions Turn Off the Water. Locate the fixture shutoff valve on the cold water supply line under the kitchen sink. Disconnect the Faucet Water Line. Connect the Tee Adapter. Connect the Faucet and Refrigerator Supply Tubes. Connect the Supply Tube to the Refrigerator. Turn on the Water.

How much does it cost to install an ice maker water line?

The price to install a water line ranges from $70 to $130. However, if your new fridge doesn’t have an ice maker or water dispenser, you can skip this step. You also won’t need a water line if the model you’re replacing already had an ice and water dispenser.

Can I use plastic tubing for ice maker?

To hook up a refrigerator ice maker, you will need to connect a line of plastic or copper tubing to a cold water line to carry water to the refrigerator. Plastic tubing is less expensive and easier to install than copper.

Does a fridge need a water line to make ice?

A water line allows you to make ice in your refrigerator. Refrigerators that feature built-in water dispensers or automatic ice makers need to be connected to a water source. Fridges without ice makers or water dispensers don’t need any type of water source to function properly.

What size is an ice maker water line?

The tubing should have a diameter of 1/4-inch and can be copper line, braided steel line or plastic tubing. Many professionals prefer copper line, but plastic tubing is commonly sold as part of ice maker installation kits.

How much does it cost to install a water line for a refrigerator?

A typical water line costs between $65 and $170 to run. The cost to install a basic refrigerator on a first floor kitchen with a water line is about $250. If you need an electrical outlet installed by an electrician, you’ll need to pay an average of $220-$750 per outlet.

Does Home Depot install water line?

Our plumbing installation services are backed by a 1-year limited labor warranty from The Home Depot.

Does Lowes install water line for refrigerator?

FREE Local Appliance Delivery Includes: Connection of appliance to existing water connection, drain or external dryer exhaust for washers, dryers, ranges, refrigerators and freezers, provided the customer also purchases new connections from Lowe’s (dryer vent, range or dryer cord).

How far can you run ice maker line?

There is no maximum length, you can run the line as long as needed to reach a main water line. You can also use 1/4″ O.D. (outside dimension) copper tubing with a flared end, approximately 8 ft coiled into 3 turns that are 10″ in diameter.

Why can’t you use vinyl tubing for ice makers?

Why can’t you use vinyl tubing for ice makers? Answer: You’re right to be concerned, because plastic tubing to an ice maker is susceptible to cracking and splitting. By the way, you may notice a piece of plastic tubing rising vertically from the water valve to the rear of the freezer compartment.

Is ice maker line same as water line?

The ice maker supply line is a small plastic, copper, or stainless steel water line that feeds directly into the ice maker. If the filter is clogged the ice maker will make fewer and smaller ice cubes. To check if the filter or water line is clogged, place a cup underneath the water dispenser.

Is PEX good for ice maker?

PEX ICE MAKER SUPPLY LINE I have been using PEX material over the last year to make plumbin Pex is so easy and durable it is great in any climate. No leaking or bursting can with stand just about any pressure.

Do ice makers need plumbing?

All built-in ice makers require a dedicated water line. Unfortunately, this may require you to hire a plumber for installation. If adding a water line is not an option in your space, you may want to consider purchasing a portable ice maker.

How long should a refrigerator water line be?

Only supporting it, and there is no requirement as to how it must be supported. Every 6 feet on 1/2″ copper pipe is sufficient for support.

How high should a refrigerator water line be?

I usually see it just above floor-level, but I’d probably install mine at about 36″ (with the electrical outlet above and off to the side of it). It’ll be easier to keep the hose from getting caught underneath when you slide the fridge back.

What can I use instead of a saddle valve?

A similarly DIY-friendly but more reliable alternative to a saddle valve is a push-fit tee connector designed for ice makers and water dispensers. You install these by cutting out a short section of pipe and installing the tee right into the water line, then you add the small supply line leading to the appliance.

How Much Is a Home Depot delivery?

A $59 delivery fee applies to any major appliance purchases below $396. Haul away of old appliances at additional charge. Offer valid only at participating stores in U.S., Guam and Puerto Rico The Home Depot® stores and on select major appliance purchases on

What is polyethylene tubing?

Poly tubing, often referred to as PE tubing or polyethylene tubing is a flexible, lightweight, durable and corrosion resistant plastic that can be used for a wide range of liquid, gas and fluid transfer applications. Poly tubing is also FDA approved for use in food and beverage applications.

What is ice maker tubing made of?

Copper and plastic are two common materials for an ice maker water line, which is vital for refrigerators with water dispensers and ice makers.

What is the best material for a refrigerator water line?

The best material for your refrigerator water line is braided stainless steel, however, that can cost a lot of money. Between plastic and copper, it really depends on preference. Copper is strong but it corrodes and gets kinked. Plastic is a good choice, but it’s not nearly as strong as copper.