Table of Contents
Drain some water. You are going to be lifting the lower side of the pool, so you need to get rid of some of the weight. Remove blocks. When you installed the pool, you put leveling blocks under the slab. Raise the wall. Replace blocks. Repeat. Fill the hole. Refill the pool.
What do I do if my above ground pool is leaning?
Severely unlevel pools need to be drained and completely taken down to relevel them. Draining at least half of the water and repositioning your leveling blocks will protect your pool from wall and water level problems. However, if you have issues with your liner, you may want to consider completely draining the pool.
What is the easiest way to level an above ground pool?
Leveling The Ground (Step-by-Step) Step 1: Find The Right Location. Step 2: Clear The Site. Step 3: Create Your Leveling Device. Step 4: Fix The Bumps And Holes. Step 5: Smooth It Out With Sand. Step 6: Compact The Sand Down Hard. Step 7: Lay Your Base Protector Down. Step 8: It’s Time To Start Setting Up Your Pool.
How off level can an above ground pool be?
Any more than two inches is unacceptable. Intex pools that are three inches off or more will not last and no one should be swimming in one. In an extreme case, the pool will collapse from the pressure. If your above ground pool is off by three inches or more, it needs to be taken down, leveled and reinstalled.
How do you level a pool once it’s filled?
Drain some water. You are going to be lifting the lower side of the pool, so you need to get rid of some of the weight. Remove blocks. When you installed the pool, you put leveling blocks under the slab. Raise the wall. Replace blocks. Repeat. Fill the hole. Refill the pool.
Does an above ground pool have to be perfectly level?
Traditional above ground swimming pools are leveled at their bottom track. The bottom of an above ground pool doesn’t have to be level. Some will “dish out” the bottom of their pool so it is gradually deeper in the very center and that’s cool as it may make it easier to maintain the pool later on.
What happens if your pool isnt level?
The water will press with more force on one section of the pool than the others. This uneven weight distribution can buckle, twist or even collapse the pool wall, resulting in property damage and injury to anyone in or around the pool when it fails.
What should I put under my above ground pool to level?
Concrete is probably the best option since it is usually 100% level and smooth. Also, grass can’t grow through concrete and animals and bugs can’t damage or burrow through it either. Grass or dirt is also another great option, as long as it has been properly leveled and you’ve killed off the grass first.
How do you flatten the ground for an above ground pool?
STEP 1: Determine your location and remove any large rocks or debris. STEP 2: Place 2x4s on the site and place a level on top. STEP 3: Add or take away soil until the ground is level. STEP 4: Repeat the process until the entire area is flat. STEP 5: Rake any remaining rocks or debris and tamp the ground.
How do you set up an Intex ground pool uneven?
To set up your Intex pool on uneven ground, Start by outlining your pool on the floor. Use a stake and place it at the center of the place then tie a string to it. Measure the string to the radius of the pool and add 1 foot to the measurement.
How do you level a sloped yard for a pool?
Place stakes or sticks at areas that slope or are off-grade. You’ll need to dig away these area in order to create level ground for the pool. Dig away soil instead of building up low patches. Always dig away slopes and high spots to make them level with lower areas, even if it takes more work.
How do I level my pool water?
How to Lower Your Pool Water Level Start with your pump OFF. Open the two-way valve if there is one. Move the multiport valve to “WASTE”. Turn the pump ON and run until you reach the desired water level. Turn the pump OFF. Move the multiport valve back to “FILTER” Close the two-way valve if there is one.
Can you shim an above ground pool?
Then there is a good chance that they have sunk into the sand. You can try to remedy this by leveling the structure with shims. The sand must still be too loose and no longer provide a level surface. If the pool tilts for more than two centimeters, you will have to empty the pool.
How do I level my pool without sand?
Pivot the plank around the pool area and level continually until you are pivoting 360 degrees without stopping. Next, you can spread a layer of crushed limestone over the pool area and seal it by wetting, tamping, and leveling it with your base. Now you can add your soil and limestone until it is flush.
