QA

How To Light Patio Heater Manually

Can you light a patio heater with a lighter?

Light the Patio Heater You can use any kind of lighter that you may have, but a candle lighter is the safest way to avoid burning your fingers. Once the candle lighter is in the hole, light it, and your patio heater should begin to get hot.

Why is my patio heater not lighting?

It may be as simple as the gas valve on the propane tank being turned off. Yet another reason your patio will not stay lit is that the gas valve orifice is blocked. You should clean the orifice or have it replaced. Sometimes there is air in the gas line which is blocking propane from getting to the heater head unit.

Can you light a propane heater with a lighter?

Propane heaters are fantastic devices for warming up an area in very little time. To light the propane heater, all you need is a propane tank and matches or a lighter. Switching it off when you’re finished is easy; just make sure you store it away properly to prevent damage.

Can you manually light an outdoor heater?

Ensure there are no leaks and the heater is in good repair. For automatic ignition systems, hold the control knob in and use a lighter to ignite the flame. For non-automatic systems, turn the control knob to the lowest setting and use a lighter to ignite the flame.

How do you light a gas heater with electronic pilot?

If you have a gas furnace, here are the steps on how to light a pilot light. First, locate the pilot valve on the furnace. Find the gas valve and turn it to the “off” position. Turn the valve to the “pilot” position. Press and hold the reset button. If the reset button fails, ignite the lighter.

Why will my gas heater not stay lit?

Some common causes include issues with the thermocouple and pilot tube. The thermocouple detects the pilot light via sensors. A dirty pilot tube can also prevent the pilot from staying lit. If the pilot tube is dirty, let the furnace cool down and turn off the gas.

Why won’t my pilot light stay lit on my propane heater?

If the thermocouple is too far from the flame, this can cause the pilot to go out and shut down the propane heater; you can fix this easily by moving the thermocouple closer to the flame. The thermocouple could also be worn out, in which case it needs to be replaced.

Why does my patio heater have a yellow flame?

A yellow flame is incomplete combustion. Try opening the air shutters more. If it is propane, see that it is properly converted. If the burner tubes are dirty, take them out and clean them, or replace them.

How do you bypass a thermocouple on a patio heater?

To bypass the thermocouple: Move the tilts switch wire aside. Remove your thermocouple from the heater using an 8mm wrench. Pull the valve housing aside using your 13mm socket wrench. Remove the valve using your pliers. Put your thermocouple back into position.

What does a dump switch do?

A dump switch is a safety device on propane heaters that shuts off the gas if the heater gets knocked over. When the heater is standing upright, a small weight inside the dump switch presses down, completing the circuit and allowing gas through to the heater.

How does a patio heater gas valve work?

The thermocouple is what signals the gas valve to open and deliver gas to the burner. If these ports are restricted in any way, the outdoor patio heaters will not have a strong pilot, and in some cases, may not even have a pilot at all. This means your unit will not turn on or will struggle to turn on.

What does a thermal coupling look like?

What does a thermocouple look like and how do you find it? The thermocouple is made up of a tube, a bracket, and wires. The tube sits above the bracket, a nut holds the bracket and wires in place, and underneath the bracket, you will see the copper lead wires that connect to the gas valve on the furnace.

How do you light a pilot light on a lighter?

With the button depressed, hold the lighter flame near the pilot opening. Continue holding the gas valve to the “Pilot” position for at least one minute after relighting the flame. This allows the thermocouple safety sensor to heat up properly.

How do I turn on electric heater?

Electric Heaters For new wall heaters, turn the dial towards ‘Pilot’ and press down on the ‘Ignite’ button. You will have to press the button, again and again, until the pilot light starts from the spark. When the pilot light starts, continue holding the button for about a minute. Then, release it.

What do I do if my pilot light won’t light?

If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.