Table of Contents
What should I put under my hot tub?
Gravel is an excellent choice for a hot tub base. It’s relatively cost-effective and easy to install, plus it’s very good for drainage. This is important because you need to make sure any rain water or overspill from your hot tub is able to drain away from the base. And unlike concrete, gravel won’t crack over time.
What is the best base to put a hot tub on?
A concrete surface is an excellent base for your hot tub as this material is extremely sturdy and long-lasting. If you have an existing patio made of concrete bricks, make sure it’s in good condition and is level (not angled for drainage). A customized poured concrete pad is an even better choice.
How do you prepare the ground for a hot tub?
Place a layer of gravel on the leveled spot. The thickness of the layer will depend on the size and weight of your hot tub, but a layer four to six inches thick should be adequate for most hot tubs. Extend the gravel out around the tub in all directions, to avoid having a muddy area around your hot tub.
What size pad do I need for a hot tub?
The spa pad should be at least the size of the spa. If you are going to pour cement pad put a slight slope in it so that water won’t pool under the spa. A 3/4″ slope in a 10 foot wide cement pad is adequate. If you use bricks or patio blocks, they should set on at least a 3″ base of sand, pea gravel or crushed stone.
How thick should a slab be for a hot tub?
Concrete Slab The base of reinforced concrete should be about 4 inches thick and be able to withstand a weight of at least 115 pounds per square foot, especially for larger spas. The concrete should be fully cured prior to placing the tub.
Is it OK to put a hot tub on pavers?
A hot tub can be placed on pavers, but ensure that they can bear the weight of the hot tub, including water and persons. Ensure that the floor is level and solid. Most pavers are laid at an angle to improve rainwater removal. Such a slope is not suited for a hot tub.
What is a hot tub pad?
Spa pads are wonderful hot tub accessories that provide a sturdy base for most hot tubs, while still allowing for flexibility in location. People who opt for an indoor hot tub typically use spa pads so that they won’t need to do any major renovations, however, spa pads can be implemented outdoors as well!Oct 30, 2019.
Can I put hot tub on grass?
Can a hot tub go on grass? A hot tub CANNOT sit directly on grass or earth. A hot tub holds too much weight to sit on grass. It will inevitably sink, the environment beneath the hot tub will be wet and untidy and it could lead to rot if you have a wooden framed spa.
How far should a hot tub be from the house?
Best Location for an Outdoor Hot Tub Proximity to the house. To reduce the risk of electrocution, place your tub at least 16 feet away from overhead power lines. To protect your home and outbuildings from potential flooding, keep it at least 5 feet from any structure.
Can you put hot tub on dirt?
Short answer is: Yes. Gravel is an excellent base for hot tubs because it allows for drainage of water while being sturdy enough to handle the high weight of a hot tub.
How do you make a gravel pad for a hot tub?
Gravel Base Remove the sod from a section of lawn that is large enough to hold your tub. Dig out an area several inches deep and make sure the ground at the bottom is pressed flat. Fill the hole with gravel and press it down to make sure it will not shift or sink once it has weight on it.
Should a hot tub be in the sun or shade?
It’s important to take care of your hot tub in summer to avoid overheating and damage from the sun. Regular cleaning can help maintain your hot tub cover, as well as providing shade so your tub isn’t in direct sunlight.
How long should concrete cure before putting a hot tub on it?
They said one week is the MINIMUM; they said it takes up to 28 days for the concrete to completely cure, so they recommend 28 days before putting something really heavy (like a hot tub) on it.
How level does a hot tub pad need to be?
There should be a maximum of ½” (1.27cm) slope in an 8′ (2.44m) run. Do not use shims to level the spa, this could create tension on the spa shell which might result in damaging your spa. Because your spa pad must provide continuous support for the entire base of the spa, you should never level it with shims.
Do you need rebar for hot tub pad?
On top of the foam board or ground if you don’t put down foam board, put down a wire mesh layer. Install stand offs, the orange thingies, (center picture-right), then ½” steel rebar, crisscrossed and spaced 12” apart. You will also need to connect a bond wire to the rebar grid that will connect to electrical grounding.
