Table of Contents
How much do bookshelves cost to build?
The cost to have built-in bookshelves installed averages $2,676 or between $1,275 and $4,091 for a carpenter to do the job. If you buy the materials yourself, you can usually get a handyman to install them for $30 to $130 per hour. For high end custom work, expect to spend $150 to $1,200 per linear foot.
How do you make a solid bookcase?
Is it cheaper to build your own shelves?
The pros of DIY shelving include: Lower Cost – Generally, buying the materials for your garage shelves should be cheaper than purchasing prefab – just make sure you do everything right the first time. Durability – As long as you choose quality materials and a solid design, your DIY shelves will be more durable.
How deep should bookcases be?
Shelf depth for a general purpose bookshelf is usually 10 to 12 inches. Shelf spacing will generally range from 7 to 15 inches with 8 to 12 inches being common for bookshelves.
What tools do I need to build a bookcase?
As for basic tools, you’ll need a portable circular saw, hammer, block plane, combination square, tape measure, metal rule, two clamps, nail set and putty knife. Other supplies include glue, nails, sandpaper, wood filler and varnish or paint and shellac.
Is Pine Good for shelves?
Avoid using particleboard, MDF, and softwoods like pine for bookshelves. They sag under a lot of weight, dent and scratch easily, don’t offer long-term rigidity, and require extra support for long spans.
What is the backing of a bookshelf called?
I’ve used 1/8″ luan to back a bookshelf before and it did well. It’s also known as “door skins”.
How thick should Wood be for shelves?
Use 3/4-inch thick materials for shelves and bookcase structure. If you’re using hardwood solids, it’s OK to boost the thickness to 1 1/4 inch for almost unlimited support. This type of shelf looks more like a mantel and is expensive, but adds the opulent look of craftsmanship.
Why are shelves so expensive?
Bookshelves made from high-quality strong woods are very expensive, especially when you have to buy a ready-made one. Their superior structure and durability make them so expensive that you will have to think twice before buying.
What is Ikea Billy bookcase made of?
Construction. The shelf parts are made of plastic-coated or veneered particle board. The edges are covered with plastic strips. The shelves are placed on metal support, the holes in the side walls have a distance of 32 mm.
What type of wood is used for floating shelves?
Best Wood for Floating Shelves The best wood is any hardwood like solid walnut, oak, pine, maple or mahogany to name a few. Rough cut wood is more raw and will show some impurities. Finished or unfinished? some floating shelves will come finished with a stain or clear coat and some will come unfinished and paintable.
How do you face bookshelves?
Stand a level on the side of the bookcase. If the level shows that the bookcase is leaning to one side, tap on the side of the bookcase with a rubber mallet until the bookcase is level. If it won’t stay in place, tighten the screws slightly and tap on the case until it stays level.
How much weight can a bookshelf hold?
Strength Comparison: The amount of weight a 3-foot 1×12 shelf can hold without sagging more than ¼ inch: Oak: 313 lb. Pine: 200 lb. Plywood: 129 lb.
Will plywood shelves sag?
A 30” wide adjustable shelf that is 10” deep, made of any of these three (plywood, poplar, pine) materials, will have an acceptable sag for a load of up to 35# per foot, or about 90# for the entire shelf. Sag definitely won’t be a problem for those small adjustable shelves.
How do you cut a bookshelf in half?
It’s a straightforward process involving a circular saw and a few hand tools. Measure the distance from the floor to the ceiling. Mark the measurements you took across the back and both sides. Turn on the saw. Tip the bookcase on one edge. Cut across the side, using the guide the same way as before.
Do bookcases need to be fixed to the wall?
Bookcases do not need to be fixed to the wall unless circumstances call for it due to safety reasons. It is recommended that you fix your bookcase to a wall if you have pets or small children, or if you live in areas that are prone to earthquakes.
How thick should plywood be for shelves?
The most common size used in shelving is a 3/4 inch thickness. Cabinetry, furniture, and smaller decorative projects might generally use a combination of 1/2 and 3/4 and occasionally 1/4 inch.
Does Home Depot cut wood for you?
Home Depot and Lowes both cut lumber (like 2x4s) and sheet goods (like plywood) purchased in-store. The first few cuts are free, but the stores reserve the right to charge for excess cuts.
What can I make with one sheet of plywood?
15 Cool Projects You Can Make From a Single Sheet of Plywood 1 Plywood Table. Aaron Wojack. 2 Plywood Hand Truck. 3 Eames Chair. 4 Plywood Stool and Standing Desk. 5 Kids Storage Bench. 6 Rock Back Chair. 7 Plywood Media Console. 8 Plywood Doghouse.
What can I use instead of bookshelf?
Wall shelves are a great alternative to a bookcase. They don’t take up any floor space, but limited wall space can also be a challenge in a small room. This set of bookshelves can be arranged to fit your needs. If you have a narrow strip of wall, stack them vertically.
What can I use for bookshelves?
18 Cheap and Attractive Ideas for Bookshelves An Old Ladder. This looks daunting, but doesn’t require too many DIY skills. Ladders and Boards. A Book. Skateboards. Stacked Tables. Boards and Bricks. Bottles and Boards. Ropes and Boards.
