QA

Quick Answer: How To Make Valances And Swags

How do you make curtain swags?

Start by hanging one end of the swag over one end of the rod. Then, hang the other end of the swag over the other end of the rod. Let the fabric in the middle drape down. When you’re finished, the draped fabric in the center should look like a regular curtain swag.

How much fabric do I need to make a swag?

Swags – Based on an average of 44″ per swag, you will need 2 yards of fabric per swag. Jabots – Double the longest length, add 4″ and divide by 36. This will give you the number of yards needed for a single pair of Jabots.

What is a jabot window treatment?

A jabot /ʒæˈboʊ/ ( listen), also called cascade or tail, is a vertical pleated piece of window treatment used with festoons or swags along the top of a window on the inside of a building.

How much material do I need to make a valance?

The obvious answer is that it depends, but you should expect to need somewhere between 1-1/2 to 5 yards of face fabric for a standard 36- to 40-inch window. For double-wide windows (about 70 to 80 inches wide), about 2-1/2 to 8 yards of face fabric is a realistic estimate.

What makes a good swag?

Good canvas swags are made from a blend of cotton and polyester fibres. This creates a finished material that is breathable, rot-proof and water-proof. Heavy Duty ripstop means that nylon has been added to the weave giving an even better strength-to-weight ratio.

How do you measure a swag valance?

Starting from the top of the pole on the left-hand side, take your flexible measuring tape and re-create the arc of the swag over to the top right-hand side of the pole. This is your swag measurement. You need to measure the lowest part of the draped swag in order to get the appropriate amount of fabric.

How do you fold a fishtail swag?

Lay your pressed fishtail swag on a flat work surface with the lining side up. Then fold accordion style. Each fold should be about 4 inches wide (as shown). You should end up with the patterned side down on the bottom fold and the patterned side up on the top fold.

What can I use instead of a valance?

Tablecloth Linens. A crafty homeowner can whip up a window treatment with any textile—even table linens! Debbie from Debbie Doo’s took pretty cloth napkins and hung them from a rod using curtain clips. The result is an easy and cheerful alternative to a traditional valance.

How long should you make a valance?

The length of the valance should be 1/4 the window height plus one inch. Using these measurements, cut a rectangle from your fabric and lining.

How wide should a valance be for a 36 inch window?

To determine the width of a valance for a 36-inch window, the Window Treatment Expert website suggests adding 2 to 4 inches on each side, adding less for narrower windows and more for wider windows. For a 36-inch window, this measurement would provide you with a valance that has a width of 40 to 44 inches.

How do you measure a window for a waterfall valance?

Measure the bottom width of your waterfall valance by multiplying the width of your window or curtain rod by 1.5. As in the example, if the window’s width is 48 inches, multiply by 1.5 and the bottom width is 72 inches.

What are swags and Jabots?

Swags & Jabots are a pre-pleated overlapping window treatment designed to fit a 1″ Double or Triple Curtain Rod Set. They may also be board mounted.

Are swags out of style?

So are these scarves out of style? No, not if you choose the fabric, color and accessories like curtain rods and knobs correctly and also hang them in proper style. Most homes around the world today show an affinity for minimalist and contemporary decor. Window scarves can be anything that you make them out to be.

What does a jabot look like?

In the 17th and 18th centuries, a jabot consisted of cambric or lace edging sewn to both sides of the front opening of a man’s shirt, partially visible through a vest/waistcoat worn over it. This style arose around 1650. In the late 19th century a jabot would be a cambric or lace bib, for decorating women’s clothing.

How many inches should a valance be?

A standard valance should have a drop of about 18 to 24 inches. You may be able to make a 16- or 17-inch drop valance work in some cases, but anything less than that may be too short.

How wide should a valance be for a 48 inch window?

Another rule of thumb used by decorators is that the window valance depth should be 1/4 of the overall window height, plus 1 inch. A 60-inch tall window, then, would call for a 16-inch deep valance, while a 48-inch window calls for a valance about 13 inches deep.

How much material do I need for a window?

Many windows need more fullness than one length of fabric will achieve. A simple rule of thumb is that a curtain is one and a half to two times the width of the area it is meant to cover. A heavier fabric will provide fullness that a lightweight fabric can not.

Where are Oztrail swags made?

PROUDLY AUSTRALIAN OWNED & OPERATED.

Are Kings swags Australian made?

Southern Cross Canvas have been manufacturing Australia’s leading range of premium Australian made canvas goods for 35 years and continue to do so. Their swag range is no exception. There are three different styles in numerous sizes available, apart of their range.

What are the best quality swags?

Best Camping Swags for 2021 Darche Dusk to Dawn – cream of the crop. Darche Nebula 1550 – roomy swag tent. Coleman Instant Swagger – festival fun. 23ZERO Bandit Swag – 4 season shelter. Oztent RS-1 Series II – a unique setup. 23ZERO Dual Swag – freestanding stargazer. Darche Dirty Dee – the ultimate tourer.