Question: How To Measure For Bifold Closet Doors

What size closet bifold doors do I need?

Select Your Size Bifold closet doors typically fit an 80.5” or 96” tall opening. Typical widths can range from 24” to 72”. For spans up to 36”, your closet doors will have two panels or one door opening from the right or left.

How do you measure a bifold door?

Take three measurements of the width of the opening — at the top, the middle and the bottom. Then take three measurements of the height of the opening — one on each side and one in the middle. Take the smallest numbers from both sets of measurements and subtract a half-inch from each to get your final width and height.

What size opening do I need for a 30 inch bifold door?

Typically the rough bifold door opening should be sized 2 inches wider and 2 inches higher than the door itself, regardless of the bifold door size. For example a four-foot wide (48”) by six feet, eight inches high (80”) Bifold set of doors, would require a rough opening width of 50 inches and a height of 82 inches.

What is the rough opening for a bifold door?

The rough opening should be 49 by 82 for a 48-by-80-inch door. This allows for 1/2-inch-thick drywall on both sides and at the top, 80 inches for the doors and hardware, and a 1-to- 1 1/2-inch space under the door.

What is the finish opening for a 36 inch bifold door?

Bifold Finished Opening Widths are true to the measurement (a 3/0 is 36”, a 2/8 is 32”, a 6/0 is 72”, etc). Doors will be undersized in width to accommodate the call-size of the bifold.

Can you cut the width of a bifold door?

The width of a bifold door can be cut up to ¼ inch on each side to fit better into a door rough opening. Tape off the side to be cut with painter’s tape then use a circular saw or planer to trim the width of the bifold door.

How much should be the gap between bifold doors?

The goal is to adjust the doors to leave an even 1/8-in. vertical gap between them (Photos 1 and 2) and an even horizontal space along the top—without allowing them to scrape on the door jambs or floor. You can’t always get the doors perfectly aligned on all four sides, especially if the opening is out of square.

Can you cut the bottom of a bifold door?

Cut the bottom edge off the doors with the circular saw. Sand the bottom edge slightly with 100-grit sandpaper. Bevel the edges slightly to give the bottom a nice finish.

What is the minimum size for bifold doors?

What Is The Minimum Size For Bifold Doors? The minimum width for bifold doors is 1400mm. In order to fill this opening size, two individual 700mm wide door panels would be used. It is unwise to build them any smaller than this as they will bind when closing.

How do you measure the rough opening for a closet door?

Framing rough opening sizes are really quite simple. Just add 2″ to the width of the actual door size. You should add 2-1/2″ to the height of the actual door. This will give you room to space the door frame off of the sub-floor.

What is standard closet door size?

The average closet door has a width of 30 inches and a height of 96 inches, though sizes can vary widely. Bi-fold doors are common closet door types, which have two panels for a single door and four panels for double doors. Bi-fold doors are available in a range of sizes to fit your needs.

How much room do you need for bifold doors?

Installing Bifold Doors The combined measurement of both doors should be about an inch less than the total width of the opening, and one to two inches less than the height of the door frame. This is to allow sufficient room for the hardware.

How wide is a 36 inch bifold door?

6-Panel Bi-Fold Door (Primed White) | HD Supply.About this item. Specifications Rough Opening Width 36 Size 36 x 80 Supplier Product Name 36 In. X 80 In. Hollow Core6-Panel Bifold.

What is the rough opening for a 36 door?

Standard Sizes A 36” x 80” pre-hung single door will use a rough opening of approximately 38-1/2” x 82-1/4” to fit. Always remember to square up your door before you nail the frame in place to assure it will close properly.

Do all bifold doors need a track?

Yes, all bifolds need some form of track system as these are what guide the door rollers. However, some door companies refer to their products as ‘trackless’ folding door systems. Trackless systems always use a top-hung system and do not need any bottom guide track running across the floor of the room.

Are bifold doors out of style?

There are a few reasons that some people use to suggest bifold doors are going out of fashion. For example, bifold doors don’t use as much glass in their design as sliding doors. While sliding doors have slimmer frames, though, bifold designs are more durable and feature more hardware.