Table of Contents
Electric Motor Bearing Lubrication Procedure Ensure the grease gun contains the appropriate lubricant. Clean the areas around the relief and fill fittings. Remove the grease relief valve or drain plug. Grease the bearing with a calculated amount of grease. Watch for grease coming out the relief port.
What can I use to lubricate an electric motor?
Mineral oils are adequate for most electric motor bearing applications. However, synthetic base oils may be required for extreme temperature applications or where longer regreasing intervals are desired. The thickener primarily serves as a carrier for the oil and prevents it from leaking out of the application.
Should you oil an electric motor?
Expert advice: When oiling an electric motor, be sure to use oil that’s specifically designed for motors. When oiling an electric motor be sure to use special oil for lubricating electric motors. Other oils could cause excess wear and premature failure.
Can you use wd40 on electric motors?
Yes, it can as WD 40 has oil base which can make winding insulation more weaker and can damage your motor. Also, WD 40 is not recommended to be used over electrical contacts.
How often should electric motor bearings be greased?
In general, for oil bath lubrication where the operating temperature is 50°C (120°F) or less, oil should be replaced once a year. When the operating temperature is between 80°C – 100°C (176°F – 212°F), oil should be replaced at least every three months.
Can you grease an electric motor while running?
Care must be taken to follow the simple rule of 1-2 seconds between grease gun strokes and to grease while the motor is running. NEVER use an electric grease gun to grease an electric motor. A disadvantage of shielded bearings is an increase in friction and temperature of the bearing.
How can I make my electric motor quieter?
Capacitors are usually the most effective way to suppress motor noise, and as such we recommend you always solder at least one capacitor across your motor terminals. Typically you will want to use anywhere from one to three 0.1 µF ceramic capacitors, soldered as close to the motor casing as possible.
Which grease used in motor bearing?
SKF LGHQ 2 is a mineral oil based grease using a di-urea thickener. It is suitable for electric motors and similar applications.Electric motor bearing grease. Designation LGHQ 2/(pack size) Dropping point DIN ISO 2176 >260 °C (>500 °F) Base oil viscosity 40 °C, mm²/s 110 100 °C, mm²/s 12 Penetration DIN ISO 2137 60 strokes, 10 – 1 mm 265 – 295.
Should you grease motor bearings?
Regularly greasing your electric motor bearing is an important part of electric motor maintenance. When applied correctly, the right grease will protect your electric motor’s bearing against damaging corrosion, reduce wear caused by friction, and act as a seal against contaminants.
When should you grease motor bearings?
Dropping point: The dropping point is an indication of the temperature at which the grease will melt or the oil will separate from the thickener. A grease with a high dropping point is desirable, given the high temperatures reached during electric motor bearing operations.
What kind of oil do electric fans use?
It is usually best to use silicone lubricant on electric fan motors because it doesn’t get as old and cakey as oil-based lubricants do. It’s also a must to make sure you’re not using any type of lubricant that’s too greasy or toxic because it can cause problems with the bearing and coils in the motor.
Do small electric motors need oil?
The short answer is no. Electric cars do not need motor oil as they don’t have the conventional internal combustion engine with all the moving parts.
What kind of oil do you use in a small electric motor?
The grease consistency preferred for electric motors is normally NLGI 2 or 3, with a base oil viscosity of 100-150 cSt @ 40°C. Other characteristics to look for include good channeling characteristics, low oil bleed, oxidation resistance, anti-wear additives, and mechanical stability.
Can you use silicone spray on electric motors?
DO NOT USE SILICONE SPRAY ON ELECTRICAL CONNECTIONS, SWITCHES, RELAYS, ETC. There have been numerous reports that silicone spray can cause contact problems in switches, noted in multiple posts regarding automotive problems.
Why use polyurea grease in electric motors?
It has very low oil separation, so it will not bleed into the motor’s windings. The LE grease also maintains pumpability at low temperatures, making it suitable for cold environments and for use with long feed lines to remote application sites.
Is Lithium Grease good for bearings?
Did you know a spray of WD-40 Specialist White Lithium Grease is a great lithium lubricant for bearings? It reduces friction on bearings and helps keep them protected from rust as well. Because it’s a superior water and heat-resistant, high pressure grease, White Lithium Grease is great for cars and tools as well.
Can bearings be over greased?
Too much grease volume (overgreasing) in a bearing cavity will cause the rotating bearing elements to begin churning the grease, pushing it out of the way, resulting in energy loss and rising temperatures. This can result in accelerated wear of the rolling elements and then component failure.
How often should a bearing be greased?
Using the chart and the formula, the bearing only needs 8 grams of grease every 10,000 hours. If your grease gun delivers around 1.35 grams per stroke, that means the bearing needs 6 strokes every 13 months; you could average it out to a stroke every 8 weeks or so.
