Table of Contents
Turn the power to your fan off for 5-10 seconds and then back on using the wall switch. Quickly press the ‘PAIR’ button on the back of the remote control. This step should be done within three minutes of restoring power to the fan. Your fan should turn on low speed indicating the pairing was successful.
How do I reset my fan remote?
There are several ways to reset a ceiling fan remote, but here’s the most straightforward: With the power off, hold down the button until the light on the remote flashes. Then, press and hold it again for 15-30 seconds to resynchronize the remote with your fan.
How do I pair my Hampton Bay ceiling fan remote?
Setting the code is fairly straightforward. To begin, turn the remote over to the back and press firmly below the arrow on the battery cover. Slide the cover off and install a 9-volt battery into the compartment. Set each slide code switch near the battery into a position of your choice.
How do I reset my Hampton Bay ceiling fan remote?
Reset your remote control. First, turn off the power. Then remove the batteries from the remote and wait 10 seconds. Replace the batteries and turn the power back on.
Why is my fan remote not working?
Perhaps the most common cause for a ceiling fan remotes not working is either a lack of batteries or dead batteries. If your remote control has an indicator light, check to see if it comes on. If necessary, place fresh batteries in the remote control, close the cover and test the control.
How do you reset the remote on a Harbor Breeze ceiling fan?
To reset your Harbor Breeze ceiling fan remote you need to turn the power off then on and then push the ‘reset’ button or ‘learn’ button under the back cover of the remote. Make sure you hold the reset button down until the light comes on and the ceiling fan speed goes to medium.
Where is the DIP switch on a ceiling fan?
Setting DIP switches The DIP switches for the receiver are located on the flat surface of the receiver. The DIP switches for the transmitter are in the battery compartment. 4-4. Raise the fan and align the slots in the canopy with the hooks on the ceiling plate.
Where is remote code on Hampton Bay fan?
Hampton Bay Ceiling Fan Receiver Location: If your transmitter has a reverse button, then the receiver will often usually be in the Switch Housing (located between the blades and the light kit). Sometimes you will find it around the top of the motor, on the side of the motor, or in the canopy, at the ceiling.
How do you turn on Hampton Bay fan without remote?
How to Use a Hampton Bay Fan Without a Remote Turn on the light switch connected to the ceiling fan. Pull the short cord hanging from the Hampton Bay fan once to turn the fan on high, twice to turn the fan on medium, three times to turn the fan on low and four times to turn off the fan.
How can I control my ceiling fan without a remote?
To control a remote-controlled ceiling fan without using the remote, add a pull cord to the pull switch on the motor module. The pull cord can be purchased from a hardware store or garden and patio shop, while the tools needed are already in most households.
Does a ceiling fan with remote need a wall switch?
While most ceiling fans are remote control adaptable, meaning a remote can be added if desired, there are some of fans that come with a remote and cannot have a switch installed (i.e. remote only). That way only a single wall switch plate is required which keeps the wall looking cleaner and less cluttered.
What does DIP mean on a ceiling fan remote?
A ceiling fan that you can control remotely has a wireless receiver attached to it. The receiver controls the speed of the fan in response to a signal sent by the remote. Push the “Dip” switch up or down, as per the instructions that accompany the ceiling fan, to set it for a specific RF (radio-frequency) signal.
How do you reset a DIP switch?
Factory Reset using DIP Switches Raise Switch-1. Power the unit Off and On. Lower and Raise Switch-1 three times.
What does DIP mean in a remote?
DIP is short for Dual In-Line Package. A DIP switch is a set of electrical switches packaged in a small box or housing. They are designed to be mounted on printed circuit boards to provide a range of electrical inputs to an electronic device based on the position of the individual switches.
Is there a universal remote for a ceiling fan?
There are many “universal” ceiling fan remote control kits on the market for overhead fans controlled by pull chains and a singe wall switch. All of them feature on/off and fan speed control. Others also offer light-dimming and thermostatic control capabilities.
What happens if you lose your ceiling fan remote?
Usually, replacement remotes come as a kit together with the fan controller inside the ceiling fan. Most ceiling fans are quite similar and can thus be used with a universal controller. This also ensures that the new remote will work with the controller.
Can I control my ceiling fan with my phone?
Activate the fan, control fan speeds, and switch on lights—all from your iPhone, Android phone, tablet, Amazon Echo, or Google Home Assistant. With BOND, you’ll be able to use these smart devices to do whatever your remote control could do. You’ll never need to reach for the light switch or the remote again.
