Table of Contents
How do you run a successful pinewood derby car?
Maintain perspective. Pinewood Derby shouldn’t be all about racing, and it’s certainly not all about trophies or ribbons. Delegate responsibilities. Establish rules. Host a car-making workshop. Hold an inspection event. Gather materials. Establish a timing system. Use racing software.
Should you bake your pinewood derby car?
Should I bake the pinewood derby block? The short answer is no, do not bake the block. The idea behind baking the block is to remove moisture which will make the block lighter. Baking might remove more moisture but the block will quickly re-absorb the moisture after it is out of the oven and cooled down.
What is the fastest shape for a pinewood derby car?
But aerodynamics rule the day, and the best shape is a simple wedge. Just like a spoiler on the rear of a sports car, the wedge shape allows as much air to flow over the top of the car without hinderance while keeping the car pinned to the track.
How do you run a Pinewood Derby heat?
Each car will run one heat in each lane. Cars receive 1 point for a first-place finish, 2 points for second place, 3 points for third place and 4 points for last place. After four heats, the car with the lowest total score is the winner of the derby!.
Do heavier Pinewood Derby cars go faster?
Much has been written about the physics of pinewood derby cars, and this is one rare case in racing where heavy = fast. Aerodynamics have little effect in such a short race, but weight does and putting the weight at the back of the car will make your car faster on the flat of the track.
What is the best weight for a Pinewood Derby car?
First, the basics: Your car should weigh as much as it’s allowed. In most races, a Pinewood Derby car’s weight is limited to 5 ounces. If your car weighs less than that, add coins or other weights. As far as where you should attach those weights to your car … well, let’s just say opinions differ.
Do fenders help Pinewood Derby?
Pinewood Derby Fenders / Air Guides Add pizzazz to your pinewood derby car with our sleek fender accessories! Fenders improve air flow over the wheels resulting in a few milliseconds of advantage, during a tight race. Both front and rear fenders are available and are typically used together.
What makes a fast Pinewood Derby car?
Weights. One of the most important ways to make a fast pinewood derby car is by adding weights. Because the cars are relatively light, they need to overcome friction and air resistance when navigating down the racetrack. Most modern tracks feature an initial slope followed by a long, flat section.
What shape makes a car go faster?
The shape of the chasis is similar to an upside down airfoil. The air moving under the car moves faster than that above it, creating downforce or negative lift on the car. Airfoils or wings are also used in the front and rear of the car in an effort to generate more downforce.
Where should the weight be on a Pinewood Derby car?
Best Location to Weight Your Pinewood Derby Car When deciding on where to weight your car, you should try to reach a final balance point of the car 1 inch or less in front of the rear axle. To achieve this, place 2/5 of the added weight behind the rear axle, and the remaining 3/5 in front of the rear axle.
How can I make my Pinewood Derby car faster?
10 Tips and Tricks to a Fast and Cool-Looking Pinewood Derby Car Bake your block. Max out your weight at the regulation 5 ounces. Use all of the graphite (dry lubricant is usually allowed). Sand and polish your wheels and axles. Check alignment. Spend time on sanding. Use a high-quality paint. Add decals!.
How tall can a Pinewood Derby car be?
The maximum height of the car cannot exceed 5 inches (Adjust this limit so that the cars will pass under your finish gate). 5. The car must have 1 ¾” clearance between the wheels.
How do you cut a Pinewood Derby without a bandsaw?
If you don’t have access to a band saw, a coping saw will do. Coping saws are economical and can cut unusual shapes and curves. Coping Saws are intended for cutting curves in thin material but they can be used for cutting your Pinewood Derby car.
Do you glue pinewood derby axles?
7. Create Glue Holes: Glue the axles firmly in their holes to ensure that they stay perfectly placed, but make sure you don’t get glue on your wheels. 8. Add Weight: Remember to make your Pinewood Derby car as heavy as the rules allow.
What is the best type of paint to use on a pinewood derby car?
ByBrittney. Pinewood Derby cars were painted over 100 times, and we selected the best paints for them. Sand and paint are the best way to apply these high gloss acrylic paints – they do not require primer or wood sealer.
How much weight does paint add to pinewood derby car?
Paint only adds a few grams (hundredths of a ounce). We generally weight up to 4.9 oz and then do the last weight adjustment at check-in.
How much clearance do you need for a pinewood derby car?
Add to Bottom of Car Race rules require that your pinewood derby car have at least 3/8″ clearance between the bottom of the car and the track. This weight is 1/8″ thick so it can be added to the bottom of the car if your car has at least 1/2″ clearance before adding the weight.
How do you make a Lego car faster?
9 Tips to Increase the Speed of Your LEGO® Race Car Make it heavy! Make sure that your tires don’t rub against the side of your car! Larger LEGO® wheels are generally faster than smaller LEGO® wheels. If you can, use Technic axles and wheels instead of the clip-on wheels, they are faster!.
