Table of Contents
How to Remove a Mantel From a Brick Wall Remove any decorative trim around the outside edges of the mantel. Insert the short end of an I-beam construction pry bar between the back edge of the mantel and a brick wall. Cut through the mounts with a reciprocating saw to release the mantel.
How are mantels attached to brick?
Lift the mantel and position it in place, aligning the holes in the back of the mantel with the support rods. Push the mantel onto the rods until the back of the mantle is against the bricks. Gently tap with a small hammer and a small piece of wood if necessary to completely align the mantel next to the brick.
How is a fireplace mantel attached?
As with many other forms of mantle or shelf, a fireplace mantel can be commonly attached to the wall with screws or lag bolts. Bolts are screwed into the wall above the fireplace before a mantel is slotted straight onto it. In this case any screws or nails may be located on top or beneath the mantel.
How do you remove an old mantle?
Place a pry bar along the side of the mantel and tap in place with the hammer if it is a full mantel. Begin at the top edge and pry the mantel off the side of the fireplace. Move the pry bar down the side length of the surround; tap the pry bar in place and pry the side piece off until you’ve removed the entire piece.
How do I remove a wall mantel?
Work the pry bar between the edge of the mantel and the drywall, starting at the lowest point, and slowly push the mantel away from the wall. If you are removing a ledge-style mantel, work from the bottom. However, if you are removing a surround, working at the base of the fireplace upward is best.
How do you attach a wood mantel to a brick fireplace?
How to Install a Mantel Remove the old mantel. Add support by drilling holes for lag shields, then install lag bolts into the brick. Measure carefully and drill corresponding holes for the wood mantel. Push the wooden mantel carefully into place using wood glue for extra support.
How do you remove a mantel from a stone fireplace?
Chip off the masonry around stone or brick corbels using a cold chisel and masonry hammer. Insert the tip of a pry bar behind the corbels. Tap the pry bar with the hammer to penetrate sightly. Pry gently until they loosen, and remove them.
How do you remove a brick fireplace hearth?
Remove Old Hearth Use demolition hammer with a chisel bit to chip away old hearth and the mortar underneath (as shown). Leave concrete hearth base and firebox floor in tact. Brush and vacuum debris and dust from hearth base. Tip: Wear eye and ear protection and a dist mask when using a demolition hammer.
How much does it cost to replace a fireplace mantel?
Install a Fireplace Mantel: national average cost The national average materials cost to install a fireplace mantel is $236.47 per mantel, with a range between $212.16 to $260.79. The total price for labor and materials per mantel is $578.11, coming in between $483.53 to $672.69.
How much does it cost to remove a brick fireplace?
If you need to remove the inconvenient or dangerous parts of a chimney or fireplace, you can avoid the massive cost of demolishing the entire system and structure. A partial chimney or fireplace demolition costs $500 to $2,000. A complete removal could run $4,000 to $6,000.
What are the parts of a fireplace mantel called?
The fireplace mantel comes in two major parts: the lower mantel and the optional overmantel. The main parts of a lower mantel include the shelf, legs, header, inner trim, and hearth. The main parts of the overmantel are crown and wall cladding tiles.
How do you attach wood to brick without drilling?
The best way to attach wood to brick without drilling is to use a brick wall hook. These hooks are designed for brick walls, even slightly curved ones. They are removable, adhesive-free, and strong (holds up to 25 lbs). You can install them in seconds and most importantly: no holes to drill.
How do you update an old brick fireplace?
There are a ton of options for things that you can do to change the look of a brick fireplace: Whitewash or paint the brick. Stucco over the brick. Add tile to the surround or whole fireplace. Add a new mantle to the existing fireplace.
How hard is it to remove a fireplace mantel?
If you’re ready to change the look of your room, removing the mantel can create a new look instantly. If it’s screwed into the wall, use a screwdriver to loosen the screws and lift the mantel away from the wall, instructs Fireplace Universe. If it uses nails, pry it free from the wall using a pry bar.
Can you remove stone from fireplace?
What do you suggest? AIt’s certainly possible to remove a stone facade, using a cold chisel and mallet or a demolition hammer, which you can rent. But it would create a huge mess, and then you’d need to invest in new stone or brick or whatever covering you choose.
Can you remove brick from fireplace?
A: Yes, you can remove the brick facade and replace it with another material. And you will still be able to use the fireplace. The only restriction is that the material around the firebox must be noncombustible. Common choices are marble, some other type of stone or tile.
Can you remove a raised fireplace hearth?
You can get rid of the raised hearth, but remember that code requires at least 18″ of non combusitble material in front of the opening (requirements could be more depending on the jurisdiction and size of the firebox oepning) so you will have to put in a new hearth at floor level.
Do you install mantel before or after stone?
If you’d like to have a mantel, it is ideally installed in conjunction with the stone veneer so this decision should be made along with the selection of your stone. There are several different materials that can be used to create a mantel, such as stone, painted wood, or natural or stained wood.
How do you remove a fireplace mantel?
Pound the bottom of the mantel shelf with a rubber mallet to separate it from the wall if it doesn’t release when you pry the base of the mantel away from the wall, advises Fireplace Town. Tap it gently, but with enough force to pull the nails from the wall. Once it’s loosened, pull out on the shelf to remove it.
How do you remove a brick fireplace?
If you didn’t have to remove the chimney, start at the highest exposed bricks in your firebox. Place the chisel against the mortar between the bricks and hit the handle with a hammer to break the pieces off. Stack or throw the bricks into a wheelbarrow as you remove them.
Can a fireplace hearth be removed?
Removal Process Fortunately, hearth removal is a simple process. Once the surrounding floor has been protected, the hammer and chisel are used to chip away at the hearth until it has been removed.
Is removing a fireplace a good idea?
But losing a fireplace can affect a home’s appeal and possibly even its resale value, real estate pros say. A fireplace can particularly be viewed as a valuable amenity in colder climates, and removing one could even reduce the number of buyers drawn to a property, some agents say.
How easy is it to remove a fireplace?
If it’s a wooden or tiled surround, it can be as simple as removing screws and lifting it away. You may need some help with tiled surrounds due to their weight. It’s also important to wear gloves and protective goggles if you choose to break them up with a sledgehammer.
Can you remove a fireplace in the middle of a room?
Consider a partial fireplace removal Alternatively, you can leave the stack and remove only the fireplace and chimney breast (the part that protrudes into the room) below the roofline. Just note that a partial removal may require help from a structural engineer to ensure the building’s structure remains sound.
Can you drywall over fireplace?
A brick fireplace gives your home a nostalgic feel, especially around the holidays when stockings are hung with care. To remodel your brick fireplace you can simply cover it with drywall. The end result is a smooth wall that you can paint and decorate anyway you like.
