Table of Contents
Here’s how to do it: Plug your LED strips in and turn it on for a few seconds. Turn it off then take out the power adaptor without turning off the remote control. Press and hold the power button for a few seconds then connect the power supply again.
How do I reset my Smart Strip light?
How to factory reset smart light strips from C by GE and Cync Start with the light switched off for at least five seconds. Turn the light on for eight seconds. Turn the light off for two seconds. Repeat this process five more times. The strip will flash three times if the reset has been successful.
How do you reset WIFI LED Strip Lights?
press and hold the power button of wifi led controller for 5-6 seconds , then you can reset the light strip controller again.
How do you use the DIY button on LED strip lights?
How to Make a DIY Color on LED Lights Strip On the DIY mode button areas, press the up and down arrows to increase or decrease the intensity of the red, green, and blue base colors and show richer colors. After this, press “DIY1” again for the remote to auto-save your color adjustment under “DIY1” mode.
Why is my smart light not connecting?
Make sure the Wi-Fi network is a 2.4 GHz network. The Smart Wi-Fi Light will not connect to a 5 GHz network. If your Smart Wi-Fi Light is already on the right frequency, make sure that your phone is not using a VPN app in the background. The Wi-Fi connection may not have good coverage during set up.
Why are my strip lights not working?
Bad Pin Connection – If your LED strip light fails to turn on at all, then check your pin connections. Most likely, the pin is not inserted correctly. In rare cases, the pin is faulty. If your RGB strip lights won’t change colors try flipping your strip light around and reconnecting it.
What does DIY mean on LED light remote?
Using the “DIY” buttons on the controller you can create custom colors. When you press one of the six DIY buttons, the color will change to white, from there, use the color coded arrows on the controller to change the color to whatever you like!.
How do I get my LED lights to change color?
Here are the steps: Take the paper and cut them into rectangles. The size would depend on the size of your LED; just cut enough to wrap each bulb from the outside. Take your colored markers and shade the papers into your desired colors. Turn on your LED light and see the colorful result.
Why do smart bulbs need 2.4 GHz?
While 5 GHz runs faster, the range is restricted. Smart bulbs do not utilize download speeds, so there is little need to operate on a 5 GHz network. Manufacturers produce bulbs that run on 2.4 GHz frequencies simply because they’re more reliable.
How do I reconnect my smart life light bulb?
Reset Smart Home Devices Turn on the bulb for three-to-five seconds and then off for three-to-five seconds. Repeat this multiple times and turn it on again. If reset was successful, the bulb blinks. Turn off the bulb. Restart Discovery. Turn on the bulb.
How do you fix your LED lights when they won’t turn on?
To troubleshoot, try the following steps: 1) Confirm that your power supply’s voltage and current rating are compatible with your LED strip. 2) Confirm that your power supply is working correctly. 3) Check and isolate other accessories on the same circuit. 4) Check for any visible loose connections.
What do you do if your LED lights don’t work?
If your LED light source does not work properly, you can remove it from the lamp and try it out in another lamp with the same socket. In the best case, this lamp should be connected to another circuit.
Do LED strip lights burn out?
Typically, LED bulbs can last between 35,000 and 50,000 hours. Furthermore, since LEDs do not contain a filament, they do not burn out in the same way as incandescent bulbs. In fact, LED bulbs rarely burn out at all. Instead, they dim with age.
Is there an app to control my LED lights?
Boogey Lights® Smartphone APP. The Boogey Lights® Bluetooth controller and this APP are designed to power our multi-color and single-color line of LED strips and pods for use on RVs, motorhomes, campers, trailers, motorcycles, cars, truck, semi’s, ATVs, boats, golf carts and more.
How do I get my LED lights back online?
These are the typical steps to do that: Wait for 3 seconds then turn it on for five seconds. Repeat the 3 seconds off and five-second on the process for 4 times. On the fourth time, wait for the LED strips to show alternate lights.
How do I reset my magic light?
You have to turn your power (light switch that controls your bulb) OFF & ON 4 times (wait about 3-5 seconds each time you power OFF & ON.don’t just flick your light switch OFF & ON super fast). At the End of the 4th time when you turn in the bulb, your bulb quickly flash for about 20 seconds then your bulb is reset.
Why are my magic home lights offline?
Please check if your Smart Light is too far from router? These may reduce the wifi signal, then cause the “offline” problem. For Smart Strip Controller, please make sure the power is DC constant voltage power supply. Please try to restart the router, wait 3 minutes and observe the status of the device.
What color should I put my LED lights on to sleep?
A red light color is best for sleep because it has a low color temperature, far lower than regular sunlight. You can be immersed in red light at night without giving your body a jolt and altering your internal clock as blue light does.
Why do my LED lights change colors by themselves?
As established above, when LED strip lights don’t get enough cooling, they get overheated, and the diodes can change color. One of the biggest ways this can happen is poor air ventilation around the lighting setup. There is not enough space to carry away warm air and allow cooler air to circulate.
Can you change LED colors?
In a strict sense the color of an individual LED cannot be changed. Although you will find multi-color LED lights today, what you are seeing is not the individual LED changing it’s color. Light is emitted from the inside of the bulb by multiple diodes of different colors. This is often called a color-changing LED.
