Table of Contents
Fasten the siding – You can fasten it with a pneumatic nailer or nailing by hand. You can use corrosion-resistant screws, or you can use stainless steel or hot-dipped galvanized nails. You can nail the siding by either blind nailing it at the top or face nailing it at the bottom.
Do you nail or screw Hardie board?
What is the correct fastener pattern for installing HardieBacker® cement board? Fasten HardieBacker sheets with proper nails or screws (as listed in ”Materials Required” in the backer installation instructions) every 8” around the perimeter and all supporting studs.
How do you secure HardiePlank?
Fiber cement siding can be nailed by hand or with a pneumatic nailer. It can also be attached using corrosion resistant screws. Use hot-dipped galvanized or stainless steel nails. Nails should penetrate through the sheathing and at least 1” into studs.
What fasteners do you use with Hardie board?
Fasteners must be corrosion resistant, galvanized or stainless steel. James Hardie prefers and recommends installation of HardiePlank® lap siding by the blind nailing technique, such that fasteners are hidden by the course above. Fasteners shall be installed between 1 in. and 3/4 in.
What nails do you use for Hardie siding?
NAIL TYPE: Fasteners must be corrosion resistant, galvanized or stainless steel. Electro-galvanized nails are acceptable for use with James Hardie Siding Products, but may exhibit premature corrosion. James Hardie recommends the use of quality, hot-dipped galvanized nails.
Do you need to put thinset under Hardie board?
However, many manufacturers including, both Durock and Hardiebacker not only recommend that you use thinset under their backerboard, but they specify it and will void the warranty on their product if it’s not used. Thinset is going to create a solid surface under tile and prevent flexing that could lead to cracking.
Can you use a nail gun on Hardie board?
Overall, only two types of power nailers work best for attaching hardie siding: siding and roofing nailers. But if you must use a framing nailer, to install any James Hardie product, be sure to fit it with a quality flush mount attachment so as to control the depth the fastener is driven.
How do you fix loose Hardie siding?
You can easily fix it by cleaning it and then using caulk to patch the gap. “And it may take time to see it appear, so you won’t know right away,” Jamie reads. When siding shrinks it causes a gap to form between the planks. The best way to fix these gaps is to clean the joint and then patch it with caulk.
Can you hand nail Hardie siding?
You can shoot Hardie siding on with air powered nailers or use hand driven roofing nails to attach siding to the home or structure. The nails can be ringed- shanked or smooth just make sure you are hitting the studs in the wall. Nails drive in too high won’t hold as won’t nails that are over driven.
Can you use a framing nailer for Hardie siding?
With some overlap in nail size, you may wonder whether framing nailers can be used for siding? The answer is, yes. Framing nail guns can be used for siding installation, if the nail being used is long enough to attach the siding firmly to your exterior wood sheathing.
What happens if you don’t put thinset under Hardibacker?
It will make an enormous mess under the house (or whatever is under your bathroom). It is also more likely to make the floor uneven since it is hard to level thinset that is separated by gaps. The installation manual for HardieBacker suggests to embed it in thin-set and it should be installed over plywood.
Can I just screw down cement board?
Screw and Joints Do not use drywall screws as they are not recommended to be used to hold the backer board in place. All of your backer board pieces should be cut before they are placed on the floor. It is important to highlight that screws shall not be installed all the way down to the floor joists.
What kind of thinset goes under cement board?
An unmodified thinset (Masterblend) is fine between the Hardi and the subfloor. Tara, The reason for the layer of thinset between the cement board and the subfloor is to fill the voids/gaps between the two. It’ll keep the cement board from moving up and down.
Do you caulk Hardie board siding?
James Hardie DOES NOT recommend using caulk or “H”-jointers for the butt joints of HardiePlank® siding with ColorPlus® technology. James Hardie also DOES NOT recommend applying caulk to the horizontal overlap between siding planks (see Figure 2).
Is Hardie board waterproof?
HardieBacker® Cement Board with HydroDefense™ Technology is a long-lasting, waterproof solution for walls, floors, and countertops.
Is a siding nailer the same as a roofing nailer?
At its heart, a siding nailer is a coiler nailer designed for installing siding onto exterior walls. They look the same as roofing nailers, and they even operate in the same basic fashion. The main difference between these two types of nail guns is in the nails they use.
How do you secure loose fiber cement siding?
Loose Siding Boards This causes your fiber cement siding board to fail prematurely as it isn’t fastened correctly and could tear off more boards if the wind is extremely strong. This can be remedied by using pin back nailing to secure loose boards that were high-nailed during installation.
Can Hardie board siding be glued?
Hardie Planks resist staining, mold and other damage, making them resilient for use in the home. Hardie Plank can be used as a flooring option over a plywood subfloor, with thinset as the glue to hold it securely in place.
