Table of Contents
Overview. Use ordinary liquid laundry bleach to shock chlorinate the water system. Determine how much bleach to use, then pour the bleach down the well and circulate it through the whole water distribution system. Wait 6-12 hours for the chlorine to work, then flush the chlorinated water from your well and pipes.
How long does it take for water to clear after shocking a well?
It will usually take 4 to 8 hours to flush the well after a standard well chlorination. The water may become discolored during flushing because the chlorine may have loosened the hard water deposits in the plumbing. Caution: The chlorine must be completely flushed from plumbing system.
How much bleach does it take to shock a well?
4) Work out how much bleach will be needed: For every 50 gallons of water in the well use one quart of laundry bleach – (4 quarts in a gallon). Do not use excessive amounts of bleach – more is not more effective.
When should you shock your well?
Shock chlorination is a method of disinfecting a water well. It is recommended when a water system is contaminated with bacteria. Contamination can occur when the well is installed, when repairs are made to the pump or plumbing, or when rainfall runoff enters the well.
What happens if you put too much bleach in well?
According to AskingLot, if you put too much bleach in your well, it can destroy the good bacteria found in the well, which can be a significant problem! The company also says that you should dilute the bleach with water so the pipes do not get ruined.
Can I put a chlorine tablet in my well?
the well has been flooded or exposed to bacterial contamination in another manner, such as a crack in the well cap. Chlorine granules, tablets and liquid chlorine in the form of household bleach can all be used to disinfect your well.
Can you put too much chlorine in a well?
Avoid putting too much chlorine into the septic system, too much chlorine may kill the bacteria needed for septic decomposition. Reconnect any carbon filters (if the shock was due to unsatisfactory test results, replace with new carbon filters).
Can I put Clorox bleach in my well?
You can disinfect your well with household chlorine bleach such as Clorox, Purex or a generic brand. The chlorine in the bleach kills bacteria. Note that it may take more than one chlorination for your well to return a satisfactory test. To disinfect your well follow this procedure.
How much does it cost to shock a well?
To disinfect your well and eliminate the bacteria, you should chlorinate the well. You can hire a company that services wells to do the chlorinating. The cost ranges from $80 – $200.
Can you shock your own well?
Mix 2 quarts bleach in 10 gallons of water; pour into well. Connect a garden hose to a nearby faucet and wash down the inside of the well. Open each faucet and let the water run until a strong chlorine odor is detected, then turn it off and go to the next one.
How often should I shock my well water?
Homeowners with private wells should have their well water tested every 3 to 5 years for some contaminants, including bacteria. If these tests turn up positive for bacteria, chlorinating the well may be a way to resolve the problem.
Why does my well water turn brown when I add bleach?
The brown is the iron in the water that has oxidized as a result of the chlorination. Normally, the iron in water is in ion form and does not display itself until it combines with oxygen and forms common rust which turns the water reddish-brown.
How long does it take to get chlorine out of well?
Monitor the process, it can take 30 minutes to 24 hours or more to flush all of the bleach solution from the well. Use chlorine test papers to verify that the water coming from the outside faucet or yard hydrant is clear of any bleach solution. Flush the chlorinated water from water heaters.
How much bleach does it take to purify 300 gallons of water?
A general rule of thumb to shock chlorinate and disinfect a storage tank is to mix non-scented NSF-approved household bleach (5.25% chlorine) in the reservoir at the ratio of 1 gallon of bleach for every 1,000 gallons of water (i.e., 1 quart for every 250 gallons of water).
How do you make deep water clear?
Fill the bucket with clear water from the well. Add about 300g of HSCH and stir until dissolved. For every cubic metre (m3) of water in the well add 10 litres (half bucket) of the chlorine solution. Double the quantity of HSCH added if the solution is to be used for cleaning well linings or aprons.
What do I do if my well water is brown?
Pipe Replacement Replacing rusty pipes in your home will effectively remove brown water. It is the best way to do it if the cause of the problem is rusty pipes. On the other hand, this is often a big task and should only be done by expert plumbers.
Can you drain a well?
If your private well is running low on or has run out of water, you have a few options to consider. Possible solutions include lowering the water pump, deepening the well and drilling a new one. Depending on your location, drilling can also be performed to deepen your well and reach more water.
