QA

How To Start A Chainsaw That Has Been Sitting

How do you start a chainsaw after sitting?

Just let the saw sit for 30 min and the excess gas will evaporate. Remove the spark plug, dry it, crank over the engine a few times to dry the cylinder. Now refit the plug and try again. Set the switch to “On”, set throttle to fully open, set choke to “Off” and crank over the engine.

How do you clean a chainsaw that has been sitting?

How to Fix It Take off the gas tank lid. Put a few BBs inside the gas tank. Put on the gas tank lid. Shake chainsaw vigorously. Take off the gas tank lid. Pour out BBs and old gas. Flush out gas tank with cleaner.

Why is my chainsaw not firing?

The chainsaw’s engine is flooded with fuel. A fuel issue is one of the most common reasons why a chainsaw won’t start. If you believe fuel has flooded the chainsaw engine, pull the starter cord several times while holding the throttle, dry and replace the spark plug, and then try starting the chainsaw again.

Can you use starter fluid to start a chainsaw?

Another thing you can try if your chainsaw won’t start without starting fluid is replacing the air filter. If you have used starter fluid, then you know that you have to put the starter fluid into the air intake.

How do you start a 2 stroke chainsaw?

Pull the Start Cord Hold the saw’s upper handle with one hand. Use the other hand to pull up on the start cord. Aim for a quick, smooth stroke. Push the choke back in halfway when the engine starts to turn over.

Can you start a chainsaw without bar oil?

Running a chainsaw without bar oil will cause mechanical problems, and some serious safety issues, such as: Kickback. Chain failure.

Do all chainsaws have spark arrestors?

Chainsaw manufacturers include a spark arrestor on every model to prevent combustion byproducts from escaping the combustion chamber during saw operation and starting a fire. To access the spark arrestor, you’ll probably have to remove the muffler.

Why is my Stihl chainsaw not starting?

Common solutions for: Stihl Chainsaw won’t start. The spark plug might be defective. To determine if the spark plug is defective, remove the spark plug and inspect it. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time.

How much does it cost to fix a chainsaw?

THE AVERAGE CHAINSAW SERVICE IS $100 TO $125 If we can find ways to help save you money, we will suggest them to you. If we do not feel it is worth repairing, we will tell you so.

Can you hose down a chainsaw?

After it is soaked, pull out the chain with a hooked tool of some kind, DO NOT use your hands to remove the chain from the solution even if you are wearing gloves. Throw it on the ground outside, let all the excess solution run off and hose it down thoroughly with water.

Can you use wd40 on chainsaw?

We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.

Why is it so hard to start my chainsaw?

Old fuel collects moisture, making the fuel difficult to ignite. It’s possible the engine is flooded with fuel. To clear excess fuel from the carburetor, place the choke lever in the Off position, hold the throttle trigger fully open and pull the starter rope 5 or 6 times. Try to start the chainsaw.

How long to wait if chainsaw is flooded?

Let your chainsaw sit for 15-20 minutes to allow the fuel to evaporate from the engine and then repeat the starting instructions.

Where is the choke on a Stihl chainsaw?

The choke position is the fourth setting on the master control lever. This setting is used to start the saw when its motor is cold. Stihl chainsaws denote the choke position using a nearly horizontal squiggle between two vertical lines at the lowest position on the master control lever.

How do you start a flooded 2 stroke?

You usually need to take out the spark plug dry it of accumulated gasoline, crank over the engine (Try to start it) with out the spark plug installed, for 30 seconds to blow out and somewhat dry the cylinder of excess gasoline, re-install the spark plug and off ya go running again.

What can you substitute for bar oil?

6 Chainsaw Bar & Chain Oil Alternatives Vegetable Oil. Vegetable oil is one of the safest alternatives available to oil your chainsaw. Canola Oil. Similar to vegetable oil, canola oil is another super-safe alternative. Motor Oil. Hydraulic Fluid (Diluted) Drained Motor Oil (Diluted) Drained Hydraulic Fluids (Diluted).

Can you use vegetable oil chainsaw?

VEGETABLE OIL FOR LUBRICATING CHAIN SAWS. To work properly, chainsaw chains and bars must be lubricated.In the past, most operators have used petroleum-based oils. Rapeseed-based (usually called canola) oil is currently the most common environmentally compatible chain-and-bar lubricant.

Can you run a chainsaw without a spark arrestor?

We can’t run without arrestors here, and the fire danger is so high I wouldn’t anyway. There is less restriction without it, but cleaning them from time to time helps a lot. If it’s hot and dry, I wouldn’t risk it.

How do I know if my chainsaw has a spark arrestor?

The spark arrestor is in a different place on different models, but is part of the exhaust system, which means it will be near the spot where air leaves the motor. On most chainsaws, you will need to remove the slotted plastic muffler cover to access the spark arrestor.