Table of Contents
Starting Step 1: Place the key in the ignition switch. Step 2: Disengage the PTO by setting the lever to the PTO OFF position. Step 3: Set the parking brake. Step 4: Activate the choke. Step 5: Turn the key to START. Step 6: Set the throttle/choke control to FAST before you start mowing.
Why does my Craftsman mower won’t start?
Other possible causes include: Loose, Dirty or Disconnected Spark Plug in Your Lawn Mower: Check it out, clean off debris, re-connect and tighten. Dirty Air Filter: Clean or replace. Fuel Not Reaching the Engine: Tap the side of the carburetor to help the flow of gas.
How do you start a choke on a riding lawn mower?
How to Start a Riding Lawn Mower? Sit firmly on the seat. Start the Engine. Press the Brakes. Engage the Parking Brake. Put the Gear to Neutral. Pull the Throttle onto Choke Position. Insert the Ignition Key. Turn the Key to the Right hand side/Clockwise.
Where is the choke on a Craftsman riding lawn mower?
It is a Craftsman riding lawn mower model DLT3000. The actual choke is located in the opening of the carburetor. It is a plate that restricts the air flow into the carburetor when the throttle lever is placed in the choke/start position.
What would cause a riding lawn mower not to start?
There are many reasons a riding lawn mower won’t start—everything from stale gas to ignition switch problems. If you constantly have to charge the battery, a bad battery or failed alternator could be causing the problem. Lawn mower ignition switch problems can prevent the starter from getting current.
How do you start a lawn mower that won’t start?
If you run into problems getting your lawnmower ready for spring, try the following: Use fresh gas. Old gasoline can cause starting difficulties. Check the spark plug. Use the choke. Prime the mower. Check the air filter. Check the cables. Check for water in the fuel tank. Clear the starter cord of blockages.
Where is the spark plug on a lawnmower?
Spark plugs are typically located on the back or side of a lawn mower engine. Look for a short wire that’s about 1/4-in. -thick leading to the top of a short, cylindrical protrusion from the engine. If you’re not sure where the spark plug is, consult your owner’s manual.
How do you prime a lawn mower?
How to Prime a Lawnmower Carburetor Remove the cap from the lawnmower fuel tank. Fill the tank with gasoline and replace the cap. Locate the primer bulb on the side of the lawnmower engine. Press and release the primer bulb three times with your finger to prime the lawnmower carburetor.
How do I fix the electric start on my lawn mower?
Make sure the gas lawn mower’s engine is stopped, remove the Electric Start Key and disconnect spark plug boot. Then check around the blade and clear any debris that may be blocking it. Reattach the spark plug boot and reinsert key. Wait 30 seconds so the breaker can self-reset, then try restarting.
How do you turn on the choke on a Craftsman riding lawn mower?
How to Adjust the Choke on a Craftsman Lawn Mower Pull the choke adjustment knob on the dashboard out completely if the engine is cold. Start the engine. Push the choke knob in partially until the engine is running smoothly. Continue to push the choke adjustment knob in slowly as the engine is warming up.
Where is the choke on a push lawnmower?
There’s a variety of lawn mowers, but for an internal combustion engine, the choke valve is usually located on the body of the engine or a lever on the handle. Most choke valves are butterfly valves mounted in the manifold up from the carburetor jet.
Where’s the carburetor on a lawn mower?
The carburetor is part of the mower’s engine. Typically, it is bolted to the side or top of the engine. It is also connected to the gas tank, and will typically be located just below or behind your air filter.
How do you prime a lawn mower without a primer bulb?
In order to start your mower without a primer, squirt starter fluid directly into the carburetor via the air intake. Simply remove the air filter cover, take out the air filter, and squirt starting fluid into the air intake nozzle. Quickly replace the air filter, and start your mower. It should start straight away.
How do you start a lawn mower with old gas?
You need to run a siphon hose from the gas tank to another container in which you are going to keep the gas. Then, you just have to pump it a few times and let the gas travel from the tank to the container.
What type of spark plug do I need for a Craftsman lawn mower?
The Craftsman 4.5hp mower uses either a Champion model RJ19LM or J19LM spark plug, or equivalent, with the gap set at . 030 inch.
How do I know if my lawnmower spark plug is bad?
The spark plug in a lawn mower could be bad if: You can’t get the engine to fire up at all. You have to tug extra hard for longer than usual on the rewind. Your lawn mower loses power while moving. The gas runs out quicker than it used to.
How do you manually prime a carburetor?
Priming the Fuel Pump Disconnect the hose that connects the fuel pump to the carburetor. Spray a three second burst of starting fluid into the carburetor. Repeat the spray-and-die procedure until you see fuel begin to wet the rag on the fuel line. Reconnect the fuel line to the carburetor.
What does the primer button do on a lawn mower?
Pressing the primer bulb creates a vacuum that sucks gas from the fuel tank through the fuel lines and into the carburetor. Pressing the primer only a couple times should supply enough fuel to mix with air in the carburetor, and be ready for combustion.
