Table of Contents
If your fluorescent lighting is displaying any of the signs below, it could be a symptom of a bad ballast: Flickering. Buzzing. Delayed start. Low output. Inconsistent lighting levels. Switch to an electronic ballast, keep lamp. Switch to an electronic ballast, switch to a T8 fluorescent.
What happens when a ballast goes bad?
But there is a good chance your ballast could be the cause of your lighting woes if your lights are dim, buzzing, changing colors, or flickering rapidly. You should check all parts of the fixture, including the bulbs. If the bulbs fail to light up, then 9 out of 10 times the ballast is culprit.
When should a ballast be replaced?
When your fluorescent light flickers or makes a loud and annoying hum, a degrading ballast is the cause. The ballast takes in electricity and then regulates current to the bulbs. A typical ballast will generally last about 20 years, but cold environments and bad bulbs can decrease this lifespan significantly.
How do I test a ballast with a multimeter?
To measure it, set your digital multimeter to around a thousand ohms resistance setting. Connect the black leads to the white ground wire on your ballast. Afterward, test every other wire with the red lead. When you do this test, a good ballast will return an “open-loop” or max resistance.
Will a bad ballast burn out bulbs?
The ballast itself can go bad, which causes lights to flicker or even appear to be burnt out, when in fact they aren’t. They require maintenance and energy to power, on top of the power used to light the fluorescent bulb. They are a large part of the equation when using fluorescent lamps.
Why are my fluorescent lights flickering?
If your fluorescent bulbs flicker, most likely the problem is with the bulb itself. If the bulb is very dark on either end, it may be defective and burned out. The best way to test the functionality of a bulb is to put it into a fixture you know works. Flickering fluorescent lights can also be a result of temperature.
Do I need an electrician to replace a ballast?
Yes. In fact, you really need a locking device to replace the ballast. – An electrician replaces the ballast on a fluorescent lamp. He uses a switch on the wall to turn off the fluorescent light.
How do I know if my ballast is T8 or T12?
If no markings are available, the size in diameter of the tube is the easiest way to determine the type you have installed. T8 tubes are 1-inch in diameter and T12 tubes are 1 1/2 -inch.
How long do ballasts last?
According to the Certified Ballast Manufacturers Association, the average magnetic ballast lasts about 75,000 hours, or 12 to 15 years with normal use. The optimum economic life of a fluorescent lighting system with magnetic ballasts is usually about 15 years.
Why do my fluorescent lights not turn on?
The fluorescent tube won’t turn on No electrical power due to a tripped breaker or blown fuse. A dead or dying ballast. A dead starter. A dead bulb.
How can you tell if a fluorescent light bulb is bad?
Look for dark areas at the base of the bulb. When bulbs age and have been used for a long time, brown spots will appear. If darkness begins to form at the ends of the tube, the bulb may be near its end. While they may still light, they are wearing out and will die soon.
What does a bad ballast smell like?
A common source of these odors is the fluorescent light ballast. When called to such an incident, you typically will find an electrical odor or a haze of smoke. Overheating ballasts often exhibit symptoms. They may cause the bulb to flicker, shine, dim, or not work at all.
Can a fluorescent light work without a ballast?
Reverted question “ Can I make a fluorescent light work without a ballast?” yes, you can, but you need something to reduce the current as the bulb warms up. So, you can drive a fluorescent with a pulse width adjustable power supply, but this is what is in an ‘electronic’ ballast.
Will LED lights work if ballast is bad?
Can LED lamps work off of existing ballasts? Yes, if they have an internal driver than can work off that ballast. Philips, for example, has designed a tube that is compatible with an existing electronic ballast.
Why does my fluorescent light flicker when off?
When a CFL flickers, the cause is usually in the light switch, which is either a dimmer or a switch with an illuminate rocker. Illuminated switches pass a small amount of current even when they’re turned to the “off” position, which is enough to charge the capacitor in the CFL and cause a momentary illumination.
Is it the starter or the ballast?
In older fluorescent fixtures, the ballast, or choke, is a transformer that limits the current flowing into the tube, while the starter provides the high voltage needed to excite the tube when it is turned on.
Is it cheaper to replace ballast or fixture?
A replacement ballast costs about $10-25 depending on capacity and brand. The bite is that an electrician trip charge (which includes 30 or 60 minutes work) is going to be $75-150 probably – for about 5 minutes work on each light fixture.
