Table of Contents
What tool do I need to make tongue and groove?
Tongue-and-groove joints are commonly made on a table saw. But with the right bits, the joints can be made just as easily on a router table.
How do you do the tongue and groove by hand?
How do you join tongue and groove?
How deep should a tongue and groove joint be?
The groove should ALWAYS be slightly deeper than the tongue is long, by as much as 1/16″ for 3-inch wide boards. The reason for this is two-fold. First is to prevent problems during assembly.
Is a router plane useful?
Router planes, which are more like shoulder planes than routers, are invaluable for cleaning up and trimming tenon cheeks and other joinery, hinge mortises, inlay mortises, and more. But to do its best work, this small plane must be properly tuned. Learn how to get it that way, and how best to use this handy plane.
Should tongue and groove be glued?
The recommended glue for floating installation is Tongue and Groove engineered flooring glue. Glue placement is very important. The glue must be placed along the topside of the groove the full length of the grooved side and end.
Do you nail into the tongue or groove?
For tongue-and-groove flooring, drive a nail at a 45-degree angle through the tongue, then conceal it by engaging the groove of the next board. Be sure to countersink the nail — drive it slightly below the surface of the wood — to prevent interference in the joint.
Where do you nail your tongue and groove?
Avoid visible nail holes Install planks with the tongue up. Nail at an angle directly through the tongue and into your studs. You don’t need to nail through the face of the planks anywhere but on the bottom row and near the ceiling. Start with the bottom row first and work your way up.
What router bits are needed for tongue and groove?
Step 1: Generally speaking, it’s easier to cut the groove of a T&G joint first, then mill the tongue to fit the groove. A 1/4-in. straight bit or spiral upcut bit makes an ideal groove-cutter into the edge of a workpiece.
How do you groove wood without a router?
How to Cut a Slot in Wood Without a Router Cutting a Slot in Wood with a Jigsaw. Cutting a Slot in Wood with a Circular Saw. Cutting a Channel in Wood with a Table Saw. Cutting a Channel in Wood with a Dremel Tool. Cutting a Keyhole Slot in Wood with Mixed Tools.
Are tongue-and-groove joints strong?
A tongue-and-groove is stronger than simple butt joints due to the increased gluing surface and mechanical interlocking of the two mating pieces. As a bonus, the tongue also serves to perfectly align the workpieces during the glue-up for a smooth surface.
How thick is tongue-and-groove?
STEP 1: The usual convention for building tongue-and-groove joints is to cut the groove (or dado) first, then mill the tongue to fit it. Although the proportions of the joint parts can vary, usually the width of the groove is 1/3 the thickness of the mating part. So, on 3/4-in. stock, make your groove 1/4-in.
What is the difference between mortise tenon or tongue & groove?
The mortise and tenon joint is to introduce rigidity and strength to wood joinery and are connected at right angles. Whereas the tongue and groove joint is joined in parallel wood pieces (thus the need for a longer area for joining).
What tool makes a groove in wood?
If you want to cut a groove in a piece of wood, a plunge router is the easiest tool to use for straight or curved grooves. Using a rotary tool also works for cutting short channels, but it’s more difficult to make long, straight lines with them.
How do you cut a hole in wood without going all the way through?
I usually just wrap a piece of masking tape around the drill bit leaving the correct length exposed. You can either wrap enough layers of tape around so that it is fairly thick, or leave a “flag” of tape sticking out. Either way will let you drill to the proper depth without the risk of marking the surface.
What is a dado plane?
Dado Plane – 1/4 inch This 1/4″ Dado Plane is used to make a 1/4″ dado (groove) across or with the grain. The precision made nicker ensures a very neat and accurate dado as the wood fibers are cleanly severed ahead of the blade when planing across the grain.
When should you use a router on a plane?
The router plane is used to refine cuts which are either made by chisels, saws or machines. In use, the blade cuts in a similar way to a chisel but the blade is fixed within a wooden or metal body and has an adjustment mechanism making this a true plane.
Can I use wood glue for tongue and groove?
1 Answer. This looks like a simple white wood glue. That should be no problem here. Do NOT use a polyurethane wood glue here like Gorilla glue, as that will expand out and cause a mess, as well as possibly push the boards apart.
How long does tongue and groove glue take to dry?
Remove excess glue immediately. Once dry this adhesive is highly water resistant. Allow 24 hour drying time before subjecting flooring to normal traffic. Clean Up: Fresh adhesive – Damp cloth and water.
Can you glue tongue and groove boards?
In my experience, store bought tongue-n-groove boards don’t actually fit tightly together. If you glued this type of joint, you left a lot of air/glue spaces between the wood. Glue expands differently than wood. Check the wood with a straight edge.
Can you nail hardwood floor on the groove side?
To nail the groove, you must nail by hand, but you have a very small space in which to work. In addition, you must countersink every nail to avoid interfering with the tongue of the next plank. For most applications, this isn’t feasible or desirable.
